KRYDEX IPSC USPSA IDPA Competition Shooting Multi-Angle Adjustment Speed Shooter's Pistol Magazine Pouch Mag Holster Holder

Great.

I ordered one of these to pouches to test it out. Loved it so much I ordered 4 more. These pouches are identical to the Black Scorpion pouches. Exactly the same. The only difference is the Black Scorpion emblem. They are fully adjustable. They have a swivel tension mount so you can rotate them and cant them towards or away from your body. You can also raise or lower them on the belt mount. The only negative I have is that it takes a bit to get them mounted on the belt so they don't lend well to a rig where you're swapping or moving the pouches often. Other than that, they are a great value. One recommendation is to use Loctite on the threads once you get them to where you want so they don't loosen and move Mainly the main screw that holds the swivel mount.

They work good for the price, not top tier quality, but they perform as advertised.

I have purchased six total mag holders. I have a Wolf Tactical belt with quick release buckle. I used these mag holders right out of the box with NO adjustments. I slide them on my belt at each competition along with my holster and have had zero issues. I can move them between my belt loops on my pants and they also adjust/tilt and hold mags with no issues. I have not had a mag pop out or fall out like some reviews. I highly recommend these mag holders. I used them for double stack 9mm. I would challenge any of you poor reviewers to a shooting competition and guarantee I will beat you!

The best bang for your buck, however, it's a real pain to attach to your belt. You've got the four tiny hex bolts that are somewhat blocked by the belt attachment - really frustrating to turn a standard allen key. And the bolts are super easy to lose if you're not careful - pro tip, use tape on the back side of the bolts to hold them in place while you're tightening them onto your belt. Retention is below average, I'm using Walther PDP double stack 9mm magazines, and I can't seem to torque down the retention bolt far enough to get a snug fit. The ability to set infinite angles of cant positions are outstanding though and easy to adjust. Overall, worth the price. I wouldn't trust my life to them or use them for any important USPSA matches, but perfect for a new shooter or weekend run and gunner.

These great as long as you're using them with the right size belt. After realizing I needed a belt no more than 1.5, I bought the right size of they are perfect. Basically just slides onto the belt with just the right amount of tension to hold firm once the belt is tighten down.

I got these to fit on my current battle belt. They did not fit on the competition belt. Ultimately I had to return them. I do recommend getting the whole setup from Krydex. Just to make sure it all fits correctly inappropriately. I can recommend this product! It just did not work out for me. My belt was too thick for the mag holders to fit.

I'm running a G21 45acp magazine in these, they hold somewhat okay. The insert that is interchangeable to adjust for different magazines falls out easily. The small nuts don't lock on the back of the holder and fall out too easily. They don't offer any extra nuts in the package or any extra magazine inserts, so if you lose one, your out of luck. I've used these in two training sessions and in not sure that I keep using them going forward. Id suggest looking at another system, this one isn't user friendly enough.

These work awesome. I’m no competition shooter but I’ve ran my mags through them a ton and they have held up perfectly. They showed up exactly as they were advertised. Fast shipping as well!

They work well with Glock mags

These mag holders are affordable knock-offs of high end, competition-oriented holders which can cost 3x+ more per unit. If you are patient and handy with small tools, they can provide a low cost entry into competitive practical shooting sports. They are highly adjustable to a range of magazines and fit most common belt systems (up to 1 1/2” width). Made of plastic, they will not have the lifespan of high end units made of aluminum etc., but until you get into high frequency, intense practice and competition sessions they do the job. You have to spend time adjusting them to fit your mags, dealing with many tiny nuts and screws as others have mentioned (would be nice if company included some spares as they do tend to go walkabout!). Getting them mounted on your belt is also a bit of a pain; once you get them setup you will want to leave them on. As shown in accompanying pictures, I made a couple of mods which improved holders a bit. As they come, mag retention is by friction alone, which changes with use, temperature, etc. You can tighten the top black knobbed bolt down for secure retention, but then mags may be sticky to pull out. I epoxied 3/4” by 1/8” thick rare earth magnets to the inside center of the outer panel of each holder, so the magnet was centered over the fortuitously positioned hole through the inner panel of each holder (silver disc visible in photo). The resulting clearance is perfect for effective mag retention, without any scraping or interference and allows one to reduce the friction screw pressure, giving a secure but slick action. Note some competitions disallow magnet-only holders; it’s not clear if they would rule this system out, but if that ever was an issue one can quickly undue 2 nuts and remove the outer panels with attached magnets and use friction retention alone. Also as seen in photos, I drilled a tiny pair of holes in lower rear corners of each side of holders, and pushed through a 4-40x1” screw, with a piece of black plastic tubing as a spacer (cut to fit my mag thickness), with a nyloc nut on inner end. This addition made the mag holders much more sturdy and stable. Finally, as others have suggested, once I had all the holders adjusted so mags fit well, and got them mounted on the belt at the correct angles (tilting slightly away from belt, and slightly forward works), I applied blue medium threadlock to every nut and bolt (except top friction knob) and retightened everything carefully. Several friends use these holders as well, without modification, and seem happy. They use the holders with Krydex belts which also seem fine. I had a similar but higher-end Black Scorpion belt, on which these customized holders also work well.

Seems well built. Easy to switch to lefty holds glock and smith&wesson mags supper tight but are easy to pull out and put back so There great for speed loading but these are my first mag holders like this so i have no other brands to compare too. I will repost. If they break

Received this 2 days ago, and they are great. Packaging was great. Only thing that I question is that to adjust the angle and/or tightness of mag holder you need an Allen key which was not included. I didn't take off a star because almost everyone has allen keys. These mag holders are a welcome addition to my range days.