Onlyfire 03340 Electric Push Button Igniter BBQ Replacement for Select Gas Grill Models by Char-broil, Brinkmann, Grillmaster, Aussie,Charmglow, Kenmore, Lowes, Nexgrill, Brinkmann, Bakers, Grillware,

Needed a replacement ignitor for a ProComm / Feature Comforts propane ventless heater model MD300TBE (in owners manual also listed for MD100TBE and MD200TBE). Original ignitor part model number is DHLG-12 dated 2010, 1.5V DC. Yes, got money's worth out of this original part, over twelve years strong. Clicker stopped clicking from previous attempts to clean battery corrosion off. Looked up part at ProComm heater site and the current ignitor part number is PIMSC1-01 but out of stock. Took a chance on this one and it fits. Important to know is the hole to accept the ignitor on the heater has to be approximately 3/4 of an inch across to fit ignitor into hole. If hole is smaller, then may need to file down edge on heater a little to fit. This fit our propane heater fine with no adjustment. If you open the heater and the ignitor looks similar this should work.We bought the one plug model. The ignitor block has a flat square plug end embedded in the bottom corner. The thin wire on the heater is round looking, but it still fits on a blade end. The ignitor plug blade must be aligned with the seam in the wire plug. The existing wire on the unit looks like a round end but fits on a flat square blade. Did not think it would fit, but looked at original part blade and it is the same as new part, flat blade. Blade aligns with seam then slips on. Round wire end to square, works.For heater install. Took the screws off face of heater, unscrewed the old ignitor part, pulled off wire, positioned the new ignitor in heater hole, spun on the included plastic nut, dropped in a AAA battery, put the rubber cap on it and now clicks away like normal. This was a good price and with prime was delivered next day. Now if it lasts as long as the original then great. Just remember to take out the batteries when not in use for the season or occasionally check for leaky batteries. Hope those with a propane heater find this helpful since this is advertised mostly for bbq grills. It just basically clicks to make a spark to ignite the pilot light.

Bought a used grill on Facebook for my vacation property- I'm not there enough to really invest in a good higher end grill like I have at home. Unfortunately the grill I bought had been left out in the florida heat for a while, so the battery in the old igniton had exploded and corroded the switch. Took me a long time to figure out which part and size I needed- this switch. It took less than 10 minutes to install and for my model needed a Phillips head screwdriver. Sparked on the first try with a single AA alkaline battery. I remove the battery when not in use to try to help protect this switch. It's been used at least once daily for the past 3 months, hasn't failed yet. Highly recommend this switch, even for the technically uninspired.

Took less time to install than it did to get it out of packaging box. Using an adjustable wrench, I removed the old one & installed the replacement in about a minute. Opened gas tank & grill grill valve; pushed the igniter button and gas grill lit on first push. Turned it off & double checked it a 2nd time. Perfect!!!Broil-Mate AND Owner happy!!! Pork Chops tasted extra good.

I was able to make this work but it is much bigger than the original. The body of the device is twice as big as the original and the shaft that goes thru the hole in the grill is bigger also. You will have to file out the hole to make this work. And also positioning it is a challenge. I was able to make it work but it is NOT a plug and play replacement'

Even though it is a little longer than the original, I could make it fit and it performs just like the original.

Connections were correct. I only needed to make the mounting hole larger to accommodate the new switch. It works great.

Perfect for replacement

2 minute install, works great.

Ignitor fit properly in my grill and works great.

had to return it, only had one prong

Easy to install and came quickly. Been working now for over a year and it's better than the original which would not spark when wet.

The product works great. I had to use a uni bit and make the existing hole on my BBQ slightly bigger , but once I plugged it all in and tighten it down and put a battery in . It worked as it should. spark to all 4 igniters

Excellent product