Eagle LightsGeneration II Midnight Edition 2 Inch LED Turn Signals with White Running Lights (Front (1157) and Rear (1157) for Harley Davidson Motorcycles

The media could not be loaded. They are bright, easy to install,because i installed on a 2006 street bob ( harley ) i needed to buy a load equalizer. Went with Badlands. I had one rear turn not working, talk to Badlands tech. He was very helpful! The problem was reverse polarity, ( wires we're opposite for ground and hot). Because these leds , need hot to hot and ground to ground. You can't switch the wires in the leds , so i switched the wires from my turn signail plug ( location in the brake light) and that worked. I did buy the smoked lenses, they are not very dark, however i did end up using them. As other reviews, you will need to Dremel the inside, other wise the led s won't fit. They fit on my stock ones just fine. These led s are worth every penny. Bright as HELL !! Nothing safer then being seen! I don't normally take the time to write reviews, I hope this helps out someone.

The media could not be loaded. 2007 Harley Davidson Sportster Roadster:Very bright and quick install.Make sure you coil your cord enough and try to keep the saucer flat against the signal housing, as you reinstall the lens cover over these.My only issue is that the front signals aren't the correct amber color, they turned out more like a weak pink/red. The rear signals colors are correct.These lights are wonderfully bright, add a great deal of visibility and even add some addition front driving lighting.Even with the incorrect coloring for my fronts, I'm still fully pleased with the purchase- well worth the cost. They aren't the cheapest option and they aren't the most expensive either.Also, I do have the Badlands Load Equalizer III, to ensure correct flashing/voltage.

These lights are super bright and I love the fact that the front DRL's are white versus amber. It would be nice if the bulbs did not have the pigtail wires and had the bases attached to the circuit board. the wires make it a tad difficult to stuff it all in the housing and get the lenses to lock into place. It was a bit of a tap dance to make it work, but I was ultimately able to do so. Also, the boards don't want to sit straight in the housings for the same reason. All in all, not a bad install and I love how bright these are. Love the look.You WILL need a load equalizer if you have a '13 or older Sportster with 2 contact bulbs to prevent an error light on your "dash" and fast blinking.

I ordered these lights based on I have used this company's product before a headlight for a Yamaha. The lights are super bright don't look directly at them. I had one issue both front and rear lights on a Harley Davidson Road Glide Special have a 1157 base. I did not pay attention to this. Eagle Lights sent me a new set for the rear with the 1157 base work great. Customer service is great. If you're looking for a bright well made led light set for your Bike get these. There are other brands out there that charge double for the same quality products. Instalation was a snap 30 seconds per light. Anyone with common sense can do this.

Easy to install plug and play solution for those low powered OEM bulbs. Minus one star for the fact that the diameter of the light was exactly the same as the diameter of the cover resulting in a bit of an odd fit. It took me a few tries but I was eventually able to slip the light evenly into the cover then plug it in and attach it to the assembly. The white LEDs do quite a bit for making me visible not to mention increase side lighting at night. Very nice design and significantly less than what the manufacturer wants for a like solution.

I was very hesitant to spend so much on a set of lights. I purchased a cheap set when I bought my bike last year. Big mistake! The lights I bought worked for a couple of months and then started going out. I did a lot of research and found these. They arrived and looked to be good quality. I installed them and they look great. A lot of the other reviews said they were difficult to install, but I found that if you just twist them after getting them plugged in and the extra wire will coil up and you can just put the lens right on. Literally a 5 minute install. I will update in a few months on how they are holding up.Update November 2020I had one light that had a few of the LED’s go out. I messaged support and sent pictures of the light. Within a few days I had a new light. That light didn’t flash so I contacted them again and they sent another right out. This company truly stands 100% behind their products. Not to many that do now days. Worth every penny.

I ordered this kit and it was sent out rather fast. Received it on a Friday, and Saturday morning I installed it. I had a faulty light, got ahold of eagle and both Keith and Bob responded very quickly and set me up with a warranty claim. These guys are great and I hope the product is as good as they are. Now I just have to do their gen 3, 7 inch headlight.

These turn signals are Bright! The installation was not terrible. After reading a few of the reviews here, there is a lil trick to make sure they stay straight during install. Plug them in and before coiling the wire...fit the signal into the lens because its a tight fit. Then coil the wire and attach both lens and signal into the bullet housing. Also it states you do not need a resistor for the hyper flash for certain model years. This is correct, I have a 2017 Street Glide. However I did find out that although the turn signals themselves do not hyper flash, the turn indicators on the fairing do hyper flash. Overall these are a great turn signals