Question 1

Can this 6" damper connect directly to the ac infinity cloudline t6 fan or it need to connect to duct first then fan?

Accepted Answer

No. This has a female sized connection. The fan's diameter is for attachment of ducting. It is the SAME SIZE as the damper. A short section of duct will be needed to connect the two. Could use a 3 inch piece of 6 inch rigid duct and tape it.

Question 2

How air tight is this? Is it leaky at the center hinge or does it have gaskets there?

Accepted Answer

The individual butterflies do not have any sort of gaskets or seals around their mating surfaces as they're not meant to be a way of "sealing off" a section of air handling equipment in an "air-tight" sense of the phrase...BUT, I will say that.. up against comparable dampers available at any home improvement store or HVAC supply house, these are of a NOTICEABLY higher quality!

This may sound like a sales pitch, but I assure you.. I'm nothing more than a customer who is VERY happy with their products.

AC Infinity component are like holding an Apple product!  Even their packaging just feels "premium"!

The housing itself is very stout/heavy, made of thick (I believe) drawn metal, and not the typical thin, stamped/rolled and pinch-welded galvanized sheet metal that most others are made from.

The damper body is strong enough that I could NOT very easily get it to flex/distort in my hands.  Obviously don't try this, as it's imperative that it stay "round" in order for the butterfly flaps to operate smoothly, but that's exactly WHY I tested that, because I wanted to see how easy it would distort when manhandled.. so I knew how delicate I needed to be with the thing while installing it, laying on my back, in my hot/cramped attic.. and I was surprised and shocked at how rigid the body of the unit actually was!

I've purchased/installed several AC Infinity 6" and 8" dampers now, and both of the HVAC pro's that I've had help me with my projects have all been shocked, and have commented about how amazed they are at just how nice ALL the AC Infinity stuff actually is once they finally take it out of the box and handle it.

It does have 2 soft rubber "o-ring" style gaskets around the outer diameter, meant to create a seal with the mating sections of pipe or hose that you slip onto either end.

The butterflies are very light to operate, they move very smoothly, and the retraction spring gives them a satisfying positive "clunk" when they return to their closed position after you turn your unit off and the air pressure drops inside the duct.

The butterfly sections are center hinged, and they seat up against a drawn "lip" inside of the body of the damper, so that any back flow pressure will actually push them up against this lip, and the more back pressure, the harder it will push against them making it difficult for any sort of air mass to move backwards up the system.. but as I already mentioned, it's not a submarine portal, so by no means does it create an air/water tight "hermetic" seal, but if you're only  concerned about things like air drafts during cold weather (what it's really designed for) then you won't find a nicer damper!

Put it this way, it's not designed to be a "check-valve", or a shut-off valve, so I wouldn't try to use it to completely block-off a section of duct when not in use, or I wouldn't try to pressurize the back side of this thing with another fan, and expect it to prevent that fan's output from migrating backward/passed the damper.

A lot of people think you can have multiple fans share a single, centralized, exhaust duct as long as you install a backdraft damper behind each fan, and that the damper will prevent the other fans from backfeeding each other.. but that's just not the case.

It won't prevent things like gases, smoke, chemical vapor, or anything like that from entering a section of duct work when it's closed, but it will "seal" well enough to prevent cold back drafts, or the ingress of bird/insects, and it'll do a decent job at keeping your heat from escaping out your exhaust ducting when the fan is turned off and the damper is closed!

Question 3

Will this work on the intake side of an ac infinity fan? i want to use this to pull air from a room and not allow the air to flow back into that room

Accepted Answer

It will work on both the intake and exhaust side of the fan.  I use it as part of a room exhaust system in my setup, it blocks the backdraft of air but if will let some heat or cold radiate through the metal flaps.

Question 4

will this work with non flexible duct?

Accepted Answer

Yes

ASIN	B0842Y637Z
Additional Features	Spring-Loaded
Best Sellers Rank	#12,290 in Tools & Home Improvement ( See Top 100 in Tools & Home Improvement ) #14 in HVAC Ducting
Brand	AC Infinity
Brand Name	AC Infinity
Color	Black
Control Method	Touch
Customer Reviews	4.6 out of 5 stars 2,051 Reviews
Filter Type	Baffle
Finish Type	Powder Coated
Finish Types	Powder Coated
Included Components	Damper
Item Dimensions D x W x H	5.03"D x 5.03"W x 7.08"H
Item Form	Insert
Item Highlight	Antidraft Duct Insert w/ Airtight Seal & Spring-Loaded Aluminum Folding Blades for Ducting in Range Hoods and Bathroom Fans
Manufacturer	AC Infinity
Manufacturer Part Number	AC-BDD8-B
Material	Alloy Steel , Aluminum
Material Type	Alloy Steel, Aluminum
Model Number	AC-BDD8-B
Mounting Type	Horizontal/Vertical Mount
Noise	59 db
Number of Items	1
Product Dimensions	5.03"D x 5.03"W x 7.08"H
Special Feature	Spring-Loaded
Specification Met	UL
UPC	819137021327
Unit Count	1 Count
Vent Hood Design	Range Insert Hood
Ventilation Type	Ducted/Vented
Wattage	75 watts

AC Infinity Backdraft Damper 8" One-Way Heavy-Duty Airflow Ducting Insert

Details

Details

Description

Specifications

Common Questions