13.810 Slipfix Railbolt

Works great. Easy install. Was able to adapt for low profile railing. Tips: 1) when installing your rail, loosely tighten the starting end right away to help hold rail in place as you slant install the railing. 2) keep your first spindle from the post far enough away to allow working room to tighten the rail bolt. 3) use an excel spreadsheet to map out your spindle layout. They don’t have to be exactly the same distance apart… nobody is going to notice an 1/8 of an inch if you need to burn up some gap between posts.

Quality product- got the job done!

This made my installation so much easier that it would have been otherwise. I was installing a handrail between two immovable objects. So, there was zero wiggle room to work with. This product allowed me to install the handrail with minimum fuss and the result is rock solid. I strongly recommend doing a dry run first (3rd photo) so you can get the feel of things before the actual installation and get familiar with how everything works together. Based on some videos I watched, I took my handrail and cut off two small wafers of handrail and a third chunk of handrail that was about 3 inches long. One wafer was a template for marking the location of the center of the 1 inch forstner bit on your newel (middle photo right wafer). One wafer was a template for marking the location of the 3/8 inch hole one the end of your hand rail (middle photo left wafer) And I used the drill press on the 3 inch chunk to make a perfectly plumb 3/8 inch hole to guide my hand drill when I was making the 3/8 inch hole in the ends of the hand rail (left photo, top of middle photo). The key for me was making the templates and practicing (3rd photo) before doing it for real.

Great product. Made 2 templates out of 1” pieces of my handrail to ensure everything lined up perfect. If the nut fails or you can’t get it on, you can take it apart and get the geared nut out and put it on with a screw driver. It’s an M6 .75 pitched bolt.

These work as advertized. I recommend ordering the ZipBolt Railbolt Drill Guide which helps mark the 1" hole on bottom of the rail. It also is a life saver when drilling the 3/8" hole in the end of the rail. I opted to clamp the drill guide to the bottom of the rail so it wouldn't move when drilling. I found that there is a little bit of wiggle room if all the drilled holes and the parts aren't perfectly square. When installing the gear in the 1" hole, hold it in place with the hex bit against the the side of the hole where the bolt comes in, then slide the bolt into the 3/8" hole and screw the bolt counter clockwise into the gear so it sticks out of the end about a 1/4". Then slide the gear so the bolt is flush with the end of the rail. Then put all of the balusters in the holes in the rail, stand it up in place, line up and extend both bolts into the key hole plate in the post and push everything down. Tighten the bolts with the hex bolt bit turning clockwise. I have big strong hands so I tightened all the connections by hand. I am an experienced carpenter and it still took a fair amount of time, but the finished product was worth it.

Excellent product

Tricky to use and lay-out for the boring and machineing. Definitely want to make practice pieces and use wd-40 on the hardware till you get the system figured out. Once you have working connections use these as jigs for the real railings.

Great product. Easy to install and the result looks fantastic.

Quick, simple and easy to use. Be careful not to over tighten the catchbolt though, easily done! I know from previous experience!

Great and works well. Easy to follow instructions and makes install a breeze

The idea seems sound enough, but the product was not up to the job. It all seemed very straight forward, however, when it came to tightening the screw thread up to ensure a snugg tight fit, it didn't. Therefore, having waited for the product to do the best job I thought I could, I'm afraid it was back to good old screws. Disappointing.

Great product

Clear instructions and easy to install with common tools available at the hardware store if you don't have them already. Rail looks great and is solid. Also used Zip Bolt product to anchor newel post to floor, same experience with that too.