ZIYOO California King Bed Frame 16 Inch High 3" Wooden Slats Platform,3500lbs Heavy Duty Support,No Box Spring Needed Mattress Foundation, Quiet Noise Free, Easy Assembly

This is a nice bedframe that gives stability and storage space underneath. For 2 people: I do not recommend it on a hardwood floor, unless you and your partner don't move much - I screwed it to the wall with a 2x4 and put anti slip rubber feet under the frame legs. Also, we have had this frame now for a year and the wood planks start squeaking - easy fix: just put painting tape around the ends of the wood planks (between metal and wood). Other than that great product and good value - also, if needed to store away, super compact when put apart!

So we’ve had this frame for not quite two years now. At first it didn’t make a peep but now almost two years in and it’s starting to make lots of noise. Not sure what the squeaking is, I’m assuming the wood somewhere rubbing on the metal. But other than that it’s a great frame. I do wish it wasn’t so high but all the short ones were super expensive when we purchased this one. Very sturdy and has held up well other than the squeaking. Lol

Received bed frame today. Setup in about 30 minutes and seems sturdy. Included tools are cheap, but work for the little they are needed. I do wish there was a lip to keep mattress on frame. Can’t yet vouch for quietness. I did add stick on/non-skids to feet, considered adding under wood slats.My one complaint is that I ordered this bed frame 10 days ago. Two days after ordering I was notified there was an issue with payment. I corrected immediately and shipping got pushed back 8 days. It finally shipped on the 9th day after ordering and arrived the next day. Why did it take 10 days when it arrives the day after shipping.Bed seems great, shipping time stinks!

It took about 30 minutes or so to set up by myself but i also had to clear out the older stuff that was in the way… overall good product… Downside, no head board… but hey I’m good with it… Side note::: my wife likes how high it is!

This will be my first night on this frame, and I haven’t really “tested” it yet. But, all in all I’m pretty happy with it.Two people may make it easier, but I did it alone in about 45 minutes. 5 of that was waking to and from the garage to get a wrench after the little poc “wrench”, that comes with the kit, bent.I’ve been a mechanic for over 20 years, but you don’t need a whole lot of aptitude to do this alone. I’ll run you thru some tips to make it easier...1. Get a 13mm and a 10mm box end wrench. Don’t use that poc it comes with. The Allen key it comes with is fine. It’s nice and short so you shouldn’t accidentally over torque a bolt. Also get a tape measure, at least 12ft, so you can square it before tightening the hardware fully.2. After opening the box, inventory everything and make sure you have all the pieces.3. Lay out pieces A, B, C, D, and both E’s, in the middle of the room. The side rails (E) swing out to extend. One side is straight, one side is tapered. Extend the straight side first, then the tapered side.4. With everything laying flat on the floor, install A-D onto E. Some of the holes are drilled very well, so make sure you can get 2-3 threads going by hand. This soft Chinese metal can strip out really easy. Get all the bolts loosely installed. Flush, but with a little wiggle. Don’t worry, you’ll tighten these up later.5. The head and foot rails (F) extend just like the sides. Here’s where you can make it easy with one person.... place the rails in position and fully extend the ends with the non-tapered joint. And make sure they’re both pointing to the left (as you are looking at the bed). Stand up the left (E) rail and lean it against (F). Now, let the tapered ends of (F) (the right sides) hang to to floor and act as supports. Make sure you get both bolts thru before installing the nuts. DO NOT fully tighten at this time. Snug, but a little wiggle. Once that’s done, stand up the right rail (E) and attach it the same way. Snug nuts, but leave some wiggle room.6. Put the main support (G) in position and get all the bolts thru the holes then loosely install the nuts.7. Now, here’s where the tape measure comes into play, and why you left some wiggle to the hardware. Measure diagonally from corner to corner. If the measurements are the same, you’re square and you can start tightening all the hardware. Start with legs A-D, then do the nuts on F. Make sure you DO NOT over torque the hardware or it will snap. German torque it, as we used to say. Gütentight. If your measurements from corner to corner are not equal, then adjust the bed by shifting the bottom rail left or right until the measurement are equal. Once equal, tighten as previously discussed.8. With the rails secured, tighten the nuts holding the main support (G) in place. I purposely over torque these a little in order to recess the button heads below the side rails. Don’t go to far, but getting them flush with the E rails should help prevent some mattress wear.9. Get the frame in place where you want it. It gets heavy with the wood slats. Once in place, install the wood slats. Note: the slats are about a 1/2 inch shorter than the width between brackets. So I tried to center them the best I could.10. Now it’s time to place you fun pad on the frame. This is where two people can be useful. BE CAREFUL. The corners are sharp and if you drag your mattress across them, you’ll likely tear it! So... if you just have yourself, take some of the cardboard from the packaging and place over the corners as you slide your mattress into position.One thing I really noticed and liked about this bed in the wood slats are very smooth, which makes placing the bed very easy without snagging the mattress.Final note... I will be ordering some black pool noodles to wrap around at least 4 of the 6 legs. The first thing I did after setting this up was stub a toe on an angle and it flipping hurt! So, I’m going to wrap a black noodle around the legs and secure with a couple black zip ties.

I 1st have bought a king now about a California king I love this platform and hopefully if I need another I'll order another for another bed.

The bedframe was super easy to put together. It is sturdy, good looking, and easy to maneuver. I would buy it again.

Exactly as described. Had it 2 months, no problems. I felt the wood slats were less than high quality and may have to be replaced at some point. Easy to put together. Heavy enought frame (w/mattress) that it's not super easy to slide on tile floor. Quality equals cost of frame. Would buy again.