RadonSeal DIY Concrete Foundation Crack Repair Kit (20-ft) - The Homeowner's Solution to Fixing Basement Wall Cracks Like The Pros

I order the double kit in order to repair 2 separate cracks.Need:- Radonseal Kit- Plastic drop cloth- At least 10 mixing sticks (HD paint department has 6 in. wooden Paint Stick for 1 qt. (30-Pack))- Roll of paper towels- Wire brush on Makita drill (or manual wirebrush is fine also, comes with Radonseal kit)- Old rags- Pencils- Bucket of hot water to warm up injection foam (20 min prior to injection)- Stack of Paper Plates (for mixing Epoxy, 3 mixes per plate)- Garden sprayer (to flush ports with water)- Box of gloves (always wear 2 sets at a time, keep bottom layer and switch top layer)- Mask- Goggles (comes with Radonseal kit)- A few old towelsPreparation:- Check for caulk tube fitment in your caulking gun before opening tube- Tubes will only compress half its length, due to having 2 chambers- Measure and Mark with Pencil port placement areas (6" apart, not 8")- A dollop is roughly a 5/8" round blob- Use paper plates for mixing - about 3 triangular mixing areas around each plate- Spread plastic under crack work areasEpoxy Steps (the more difficult and tedious of the tasks):- Use separate sticks for A and B Epoxy containers when scooping a dollop on paper plate- Use 3rd stick to mix the A and B dollops together, then also use this stick to apply Epoxy.- Be thorough when putting Exoxy around the port rims (but not in center)- Work quickly to put the Epoxy around the port rim- After pressing a port to the premarked wall, smooth out excess around outside of rim with same mixing stick.- Use up rest of 2-dollop mixture for next port(s). I backbuttered the rim of around 3 ports per 2-dollop mixture.- Always work from lower ports to upper- After placing ports, start from bottom when covering the crack with Epoxy. You don't want to go too wide with crack coverage, you have to judge how much of A and B mixture to use up, relative to the length of the entire crack.- When covering cracks between and around ports, you can scoop slightly bigger dollops - try to evenly scoop the same amount of A and B.- Don't force Epoxy into crack, just paste it over surface and around outside of portsIrrigation Steps (easiest of the tasks):- Have old towels positioned under the lowest port of crack(s)- Wait until Epoxy is fingernail-hard before irrigating- TIP: I used a drill bit smaller than the port diameter to check each port to ensure that there was no buildup of epoxy blocking the center of the port to the wall. You can tell when the drill bit is hitting the cement wall based on depth and also feel of hitting cement versus epoxy.- Using garden sprayer with water, put water into topmost port and confirm that it comes out of all the lower ports.- TIP: Use the port stoppers once water comes out to ensure all ports have water coverage- The idea here is to ensure the crack is wet and that in general most or all of the ports are showing they can leak out water (if water passes through the ports, the resin will also pass through the ports).Resin Steps (the more fun of the tasks, but is also a bit messy - double gloves again):- You should be heating up resin tubes in warm/hot water 20 minutes before dispensing.- Ensure you don't lose the "restrictors" when you open the plastic bag for the tubes.- Put tube into caulking gun before taking off the blue cap and stopper (it may be easier to attach the restrictor and host after the tube is in the gun).- Add restrictor to top of tube, then screw on hose and mixing tip.- Wide end of flexible hose goes over caulking gun tip, smaller end over ports- Use the same flexible hose when switching resin tubes to save the resin in the hose.- Go easy on caulking gun trigger, slowly dispense resin, pausing at times (while foam seeps and expands a bit)- TIP: You can see your dispensing rate (should be slow) by watching the tiny air bubbles flowing through the hose.- Continue dispensing into a port until it oozes out of next higher port, then switch to that port and put a stopper on port just completed.- Repeat until all resin is dispensed from bottom port to topmost port and you can see resin coming out the top of the crack.The foam will keep expanding, even for days after the repair. I found that even with a drenching 2" rainfall a mere 12 hours after repairing both cracks the product still worked flawlessly!

This is a great product. If you’re reasonably handy you can DIY it. I repaired two cracks and the results are perfect. No more leaks after heavy rains, freeze/thaw cycles and melting snow. Some tips that helped me: read the instructions several times and watch videos. Then read the instructions and watch more videos. Seriously. This is a permanent fix. Get it right the first time or you could create a permanent mess. Mix the epoxy in small batches. It sets up quick. It also stinks until it cures, so use ventilation. If the crack goes all the way through the foundation to the outside, cover the crack on the outside (above ground) with epoxy or hydraulic cement. This will prevent the polyurethane from leaking out and making a mess. Inject water into all the ports before you start injecting the polyurethane. This ensures the ports are open and the crack is contiguous, and provides water for the polyurethane to react with. Place the pinch valve close to the end of the hose (close to where it connects with the port on the wall). This cuts down on leaks and messes when you change ports. Inject the resin SLOWLY. It doesn't set up real fast, you have time. Watch the next port carefully while injecting. You may see water getting pushed out, or the resin filling the crack before it starts leaking out. Don't place the last port at the very top of the crack and don't completely cover the top of the crack. The resin needs some room to expand.I was surprised that this was something you could DIY. Much cheaper to do it this way and you get a permanent fix. The kit has everything you need. If you need more materials, like an extra tube of resin, you can buy those separately as needed.

First of all, I must explain I’m NOT a construction guy at all although I don’t mind the occasional DIY project here and there. If it weren’t for utube, i would have hired someone else to do this and spent tons more money. I found it very helpful to watch lots of videos on the subject from many different content creators to get a wide range of examples & pick up on different techniques & potential obstacles.My situation was this...I have a house built in 1927, poured concrete foundation w/ several significant cracks both vertically & horizontally (see pics). In the past, we installed French drains & poured a concrete patio along the same foundation walls, but during rain storms water would still find its way into our basement.Because of the condition of my particular concrete foundation I decided to spend 90% of my time on prepping my walls in advance before I started any injections to repair the cracks. Grinding concrete is not fun, it can be extremely dusty (even with dust collection bags or filtering vacuum attachments) leaving clean up to be a chore but unlike caulk, after this stuff sets up it becomes solid, so solid that it can become stronger than the concrete around it once your done. So you only have one shot at this, take the time to prep the surface as necessary beforehand, although tedious, time well spent for the final result.The actual using of RadonSeal was super easy, the epoxy hardens quickly so mix up in small quantities as you go. Unless your cracks are perfectly even in width & depth, it won’t look as pretty as you see in the videos or instruction manual so lower your expectations & be ready to problem solve as you go. After injecting this product into my most significant cracks & letting it dry, I went back over & grinded it down level with its surrounding concrete (shown it a different pic, crack injections being slightly less noticeable).In addition to using RadonSeal, I used several coats of DryLock paint on the interior & caulked any cracks on the exterior between my patio & foundation, along with filling any gaps underneath my siding w/ foam spray.It’s now been 6 months, winter has hit & we’ve had several severe rain storms and NO water issues in the basement, at all! Was it all RadonSeal or did the other measures help? It’s probably a combination of both but what I do know is that I am confident that this product did what it was supposed to do and filled the cracks in my walls (I even saw some expand to the exterior cracks & filled all the way through the voids). I wish more injection material came with it because comparing like products, this wasn’t the least expensive but I can’t argue with the results.