Performance Tool M208 3,688 ft/lbs Torque Multiplier Wrench – Torque Multiplier 1-Inch Drive Lug Nut Wrench Torque Amplifier Lug Nut Remover

When I receive this item the needle wasn't centered so I realigned it,other than that it works exceptionally well

I needed a bigger torque wrench for tightening bolts and tow balls on some hitches. I figured it would do well for some heavy duty truck applications At first, I thought this beast would be overkill, but I had an idea to prove this was a good buy.After struggling to tighten 260 ft/lbs using a 1/2 inch drive torque wrench, I pulled this monster out of the case and it looked at me straight in the eyes and said, hold my beer! It then proceeded to torque down the same bolts like they weren't even there. Any questions? I replied, no further questions, Mr. Torque Wrench, sir, and undoubtedly you will have no problems torquing hitch balls in excess of 400 ft./lbs. or greater.But seriously, I like that this 3/4 drive torque wrench can torque in both directions. The ABS plastic case is good quality, has a carrying handle, plus the four snaps keep it from opening and falling out. The price point is just perfect. In fact when I purchased it was on sale plus a coupon that save some extra cash.I honestly don't have a guess whether this torque wrench would survive the daily abuse in a shop, but this is not a tool that I'd be afraid of putting to work. Two thumbs up. I'm glad I bought this.

Rubber handle was not attached when it was delivered. And i cannot get it to go on or stay on. No locking balls to hold any of it together. Handle and sockets fall off easily.

The front connector to the lug nut socket is very, very tight. Nothing will probably slip out or anything like that. This might be easier for you to use than a click type torque wrench because it is simpler. Just don't drop it or mess around with the dial.Always check that everything is aligned properly in the first place. The the needle is right in the middle of the dial.

The lug nuts on my motorhome are torqued to 475 ft-lbs. This tool takes them right off. My only complaint is the case is cheap thin plastic that won't stay shut. But that is a insignificant thing compared to the overall utility of the tool. It is worth every cent I paid.

I bought this to do a specific job. A front hub bearing on a ford truck. I have 1/2 inch and 3/8 drive torque wrenches already but the half inch one only goes to 250LbFt and the nut holding the bearing on requires almost 300lbft. I looked at a couple of other options such as getting a multiplier, but this was the best option for me since it would not require using math to get the correct torque and it would be potentially smoother than a gear type multiplier in operation. The other thing I considered was the drive portion itself that the socket actually fits on. There is a reason most half inch drive torque wrenches are limited to about 250lbft and that is the square drive portion has a tendency to twist off when you start going past that.Most torque wrenches are most accurate in the middle of their range and while the setting I needed was towards the lower end of the range, it was not all the way at the end so I felt comfortable that it would get the torque in the allowable range for my needs. I can not speak to the actual accuracy of this wrench since I have not had it tested, but the job went well and nothing has broke from being too loose or tight and it has been over two months as of this review since I did the job.

Very accurate.Good for very fine work.Does not work for removing bolts, with pliers. But that is no big deal. You want unlimited power to remove bolts.

I bought this for mounting a red-dot site on one of my handguns and it has a torque spec of 9 in/lb. I have a torque inch/pound ratchet that is measured in newton/meters and 1 newton-meter = 9 inch/lbs, so I wanted a more precise micro torque screwdriver. When I received it, it has typical torque wrench markings for adjustment so I quickly set it to 9 in/lb without reading the instruction. I started tightening the small machine hex head bolts and with little pressure, all of a sudden the screwdriver stopped torquing and spinning! My heart jumps as I first thought I broke the head of the bolt. However that was not the case. This precise micro torque screwdriver just stops tightening when it reaches the desired torque and free spins. So I tightened the 2nd machine bolt so all is good.Although this Adjustable Micro Torque Screwdriver cost quite a bit more than other options, I learned a long time ago that scrimping on tool purchases mostly costs you more later when they either wear out fast or break....or the just don't fit exactly because they are cheap and their engineering sucks.So I am very pleased to add this micro torque screwdriver to my tool box.

Este torquimetro es de gran utilidad la marcación del reloj me permite observar el torquer deseado, práctico y funcional en reparaciones automotriz

Works great for the price. Using it for four months now with no issues.

Works fine for me .

Easy to use, works well. A must for using a wrench.

Compact tool that does exactly what it should used it several times with no problems. Probably more expensive options out there that are better but for the price a good bit of kit.