Chrome Hand Control Switch Housing Caps Compatible for Harley Davidson Electra Street Glide 1996-2013

Great look and finish. For the price.you can't beat these. Fitment is a bit tight. Some of the switches dont rock smoothly as OEM beacuse of this but they still work. Ran into a couple issues after install. The starter switch was just slightly stuck after putting it back together and one the on off switch was flipped the bike immediately would start. Took me a while to figure out the button was being slightly depressed causing this. Was pulling my hair out trying to figure out why. The horn side did the same thing so I shaved the inner side of the housing to give more clearance and it fixed it. Other than that, I'm very happy with my purchase.

Nice

For me, these were unusable. The hex hole that operates the switch was too small and couldn't be made to snap into place. I tried a test fit over the exposed hex stud for the start switch to confirm that they were not a fit. I suppose they could be reworked with a small file, but it was simpler to snap the old caps back on and leave it at that. Someone on the factory line in China must have been having a bad day, I guess. (stamped "Made in China" on the box).

First of all , you'll need a modest amount of mechanical ability to install these. If you have trouble changing your oil you might wanna leave this up to your dealer. I would give this a higher rating, but quality control seems to be lacking. first set I purchased the round holes were slightly smaller than the factory switch caps. Not a huge deal , I took a drill bit the size of the holes on my existing switch caps and opened the holes up . All went well until I got to the last cap.. that last one broke. I'd suggest getting two sets . I consider myself pretty well mechanically inclined so I'm not convinced the break was an installer issue but rather just a weaker cap in the batch. my second set the holes were spot on and the cap installed perfectly. Tip for those who haven't done this before, boil some water in the microwave. let it cool a bit but still be to hot to leave a finger in it and drop your caps in . pull each one out before you install it, dry it off and snap into place. A warm piece of plastic flexes better than a cold one despite the one broken cap these looked awesome after installation

looks and fits like the original

Functionality they work . But ease of installation no . They are very hard to put on cuz you got to keep the spring in the right place and you got to separate them cuz they got to open up to go over the pin on one side and then the grooved actuator on the other side so it really is kind of a pain in the butt to get them on there they're tight . And I thought with a couple of them for 15 minutes before they finally went on I mean at the end of it they were kind of chewed up a little bit but hey at least they're new right and they work now cuz my turn signals didn't work so I had to do something about it . If you're looking for a replacement these can work but you still need a couple pics some Vaseline and some patience .........

Just as good or bad as HD to install. If your heavy handed or don't know what your doing- don't do it. One side of the switch cap has a "star" side on it that actually activates the rocker switch in question. I've done these before and still at times during the install felt like I wasn't going to make it without one of them breaking. So I won't throw BS at you, its a bit of a tedious install and the plastic is screaming to break just before it gets on the rounded end. Once done and after a few times of use they are fine, the horn and starter button spring are fairly easy to reinstall as long as they don't go flying off when you take it apart.

Installing them into the black housings really helps me see at night. Plan on a 2 hour plus installation in a WELL LIGHTED area with a clean floor. LOL

Fit perfectly on my 07 Electra Glide Classic

Not chrome at all!! Poor quality of plastic, can’t make it fit, ad to grind the inside because they are not wide enough!! There’s a side with a small gear, it doesn’t fit in the original gear on your bike… Waiste of money!!

They are NOT white as indicated in picture they are grey and do not stand out. If you are expecting weight do not waste your money and buy. I will say they did fit. They do look better than my old worn-out ones. Just not happy about misleading advertising in pictures. Because of that they get a low rating

I read the mixed reviews on these and figured I'd try them out. Only to find out they truly do look like they were spray painted silver by a 5 year old. And then they were so brittle the first one I tried to replace broke. I took my time and wasn't forcing it, and the tab snapped right off. Went back to the stock Harley one and had zero issue putting it on. Don't waste your money on these cheap pieces of garbage!

Le chrome n'est pas chrome du tout... ne vaut pas le prix demandé..