Phanteks Eclipse P300A (PH-EC300ATG_BK01) high airflow full-metal mesh design, compact ATX Mid-tower, 120mm black case fan, Black

Esta de mas decir que este case no busca estetica, si quieres algo MUY bonito ve a por la serie 300D de corsair que esta al mismo precio en 2021. Sin embargo, su calidad de construccion esta muy bien, se siente mas caro de lo que es. El unico detalle en cuanto al diseño del case seria que el espacio de la fuente de alimentacion es muy reducido para una ATX, por lo que batallaras un poco al introducirla en el case. El PRINCIPAL objetivo de este case es mantener FRIOS los componentes de tu PC, acompañado por dos o inclusive un solo ventilador, puede alcanzar el rendimiento de los modelos Airflow mas caros del mercado. Si tu plan es tener un dicipador de stock y encima escojiste una placa con una calidad de VRM custionable o que alcanza muy altas temperaturas este es tu case. Si te interesa meter una AIO Liquida en el recomiendo checar la compatibilidad antes de comprar, ya que las tolerancias son muy justas.

The p300a is a great, airflow focused, compact ATX case! I found the front mesh, tempered glass panel, buttons, etc. all to be very good quality and the case looks great. The build was fairly smooth with a few small quirks: 1) I had to remove the rear exhaust fan to seat the motherboard properly in place. The fan is almost directly on top of the rear I/O and my motherboard has a heatsink and small 40mm right there as well. Once the motherboard is fully installed, then the fan could be reinstalled without any issues. 2) The power supply space is a little tight. My power supply is 150mm long. I had to partially uninstall the HDD cage and rotate it out of the way to get the power supply in place. 3) There is one "mystery" wire that I found running from the top/front I/O to behind the hard drive cage. I thought this was a relic from the RGB controller of the standard p300 case and was tempted to cut it out of the case, but did not. Once the build was finished and powered on, I saw that there is a small, white LED light strip just under the bottom edge of the tempered glass panel. This cable supplies power to that light. 4) The front has fan mounts spaced for 120 or 140mm fans. I already had 140mm fans from my previous case. They installed fine, however, the actual cutouts for the fan blades are sized for 120mm fans and roughly 20% of the blade area for my 140mm fans was blocked. I cut the openings larger using a Dremel. This was absolutely not necessary, but made me feel better about the setup. I bought this case to replace a massive (by comparison) fractal define r4, and couldn't be happier. Much better airflow, and the system is quieter than it was in the fractal case since better airflow means the fans don't have to run as fast to cool the system.

Das schon etwas ältere Gehäuse ist selbst heute noch klasse. Die zwei besten Features des Gehäuses sind das Mesh-Frontpanel, was einen super Airflow verspricht und die vielen Features für Kabel-Management. Es gibt sogar extra Löcher im Gehäuse für Micro-ATX Motherboards, was man nicht oft sieht. Das größte Makel des Gehäuses sind die fehlenden Lüfter vorne, die man sich unbedingt dazu kaufen sollte, um das volle Potential des Gehäuses auszuschöpfen. Für den Preis kann man sich allerdings nicht wirklich beschweren, finde ich. Allgemein ein sehr gutes Gehäuse für den Preis und tolle Kühlungsleistung mit genug USB Steckplätzen oben.

I live in a small flat so needed a compact case for a full ATX Build. Following the excellent reviews the Phanteks P400A received, Phanteks updated their smaller and cheaper P300 with the same mesh panel. The result is an excellent value for money case with full ATX compatibility in a small(ish) form factor, with great cooling potential. You can read the full description of the features online but some things to note below: - the case only comes with a single 120mm Phanteks fan. I strongly advise you to add at least two additional intake fans at the front (140mm fans can be fitted but 120mm will be fine as well). - cable management is pretty good. There are three included velcro straps in the case, lots of cable tieing points and Phanteks include a good assortment of screws and cable ties with the case. - the case features a reset button - a plus for me This said, there are some minuses as well given that this is, after all, a budget case. The front panel on mine has slightly uneven gaps where it meets the steel frame on either side which suggests QC isn't a huge priority for this line of (budget) cases. The steel is quite thin and the HDD caddies are a bit flimsy. My previous case was definitely built better and out of better materials even though it was slightly cheaper. Overall, I am happy with my purchase. I have attached some photos and a video showing my complete build (R5 2600 OCed to 4GHz, RX5700XT OCed to 2000MHz core, 16GB ram a couple of NVMe SSDs and 2x2.5inch HDDs)

I like the flexible magnetic fan filters. Comes with Velcro cable ties. Good quality case for the price.