FLEOR8 Hole TL Pickguard Scratch Plate with Pickguard Screws Set Fit USA/MX Standard TL Style Pickguard Replacement, 3Ply Black

Had to do some major sanding for it to fit. It took a while, but in the end it worked. Started by having to sand the top part of the neck pick up for the holes to line up. Had to sand down about an eighth of an inch on top part of the neck slot for the neck to properly fit back on. Had to sand around the control plate. Had to sand the three bottom holes for screws to fit. Also, it is thicker than a stock fender pickguard. Because the 22nd fret hangs over the pickguard, I thought I’d have a problem with the neck lining up on the bottom of the neck slot, but it seem to fit just right. It took some work, but in the end it fit just fine. Giving it four stars because of all the work I had to put into it for it to fit properly. Other than that, it’s a great quality pickguard.

I didn’t have to do anything to this pickguard. I took the old one off and the new one lined up with the holes perfectly. Looks great and appears to be well made. My only complaint is the cutout for the bridge. It’s not centered so it looks somewhat dorky. Doesn’t affect anything else. Mine was made by Fleor and not Whomever is listed on the ad.

Fit perfectly on my Classic Vibe tele

I had to do a little trimming around the neck and the control plate to get it to fit, but I'm happy with the end result. Nice pickguard for the price.

Looks great and a perfect fit on my MIM Player tele

Decent quality for an inexpensive pick guard. It will get the job done.Watch for damage to the guard by the enclosed screws. I had to send mine back because the enclosed screws pressed down on the guard during shipping.

Very Satisfied with this pickguard 👍! Beside some necessary though minor sanding needed (I did by hand with paper and some small files, so took about 10 minutes but an electric sander or dremel type rotary tool would have taken about 1 min or even less) to make fit around the neck to body joint and control plate on my 2021 squier affinity telecaster (turned 'partscaster'), all holes lined up great! Another bonus is the protective plastic that is peeled off , there are two separate films the top one obviously came off but the bottom was airtight so i figured to just leave it (for now) for extra scratch resistance 🤓🧐🙂.. can't beat the price and quality!

Looks great on my Telecaster. Same quality as Allparts or Fender brand. Fits nice and tight. Highly recommend as a cheaper alternative. Honestly didnt see any difference between this and a name brand pickguard.

I bought this pickguard for a Harley Benton TE-20, knowing that it would not fit perfectly, as it is not an official Fender / Squier Telecaster guitar.It was not very well packaged for its long journey from China, but it still arrived in perfect condition. Two layers of protective film to peel off. No scratches or bends to the pickguard.To fit it to my guitar, I simply used some 600 grit sandpaper to remove about 1 mm of plastic (just above and below the neck pocket), and then drilled new holes into the guitar for the screws. It now fits like a glove and looks fab. Be aware that it's black and mirror-like, so scratches will look more noticeable than white for example.This pickguard is well made, with no rough edges, and is just as good as the one on my £800 guitar. It is thick enough to hold the neck pickup in place with screw mountings. Even when it gets scratched, and I replace it, it's still a good buy considering that an official Fender/Squier pickguard is 6 times the price.

Scratch plate is well made all holes lined upa fraction of the price of the fender one. I highly recommend this product

tight fit on my 20 yr old MIM but got on in the end. Looks nice with the sunburst. Arrived next day

Quite nice. Looks good, fairly decent quality and cheap. I bought it to fit a Harley Benton Tele copy and despite thinking I checked all of the measurements correctly, ir didn't exactly fit. A bit short around the bridge,tight round the beck and control plate and 5 screw holes didn't match. Not too much to correct with small files and a fine drill to pilot new screw holes and how looks great !!!

really good scratch guard, fits nicely on my squire telecaster and makes it look great