Diamond Oscillating Tool Blade Set, Multi Tool Mortar Cutting Saw Blades Precise for Grout Removal, 4-Pack

Bought this ro get a clean cut in some tight corners that my tile person went over by an 1" (not much room for error on the cut) this worked perfectly. The grout removal was very easy to clear under tr tile to make the necessary corner cut. Needed the flat and the semicircle on this project and they worked really well. Took a little work to cut the tile but it is a more a grout remover. I also tried it on a part that the tile strip wasn't applied. This removed the grout and underlay of thinset and allowed me to fit the tile edge in very easily without chipping or breaking the tile.

Why did you pick this product vs others?: Durable and well made, used to grind excess cement off concrete steps and remove rough edges.

Received the multi blade pak for floor tile grout removal. The side swing design blades 2 worked really well. My wife and I used them with Dewalt 3 speed oscillating tools to remove grout in 16×16 floor tiles. The good: the swing blade design is the best of the 3. The diamond coating lasted 3 times longer than a Milwaukee diamond coated blade that was 35 bucks for one. The Bad: the straight blade worked but not near as useful for large wide grout lines 1/4 plus. Also wore out faster (diamond coating ) than swing design. The ugly: the half moon blade is too small to reach in the grout line at depth. It doesn't have enough clearance from the oscillating head to be useful. Maybe some smaller tool designs at the head other than dewalt would work. P.S. Don't bother with carbide coated blades for this type of work, purchased a pac at Walmart and they wore out very quickly. Would buy them again. Just purchased a 3 pak of swing design to finish up the 1000 plus sq ft of floor tile grout.

Do yourself a favor and buy 2 sets. In my case I removed the grout out of 90% of our shower. I switched the blades out every 5 minutes so they wouldn't overheat which was suggested by another reviewer and that worked like a champ. Just use caution as these will damage the edges of your tiles if you aren't careful.

Great price but don’t last as long is higher quality blades

Had to cut out a 10 foot section of 4 inch tile to install accent tile in a shower. These blades cut through the grout leaving very smooth lines and no chipping on the adjacent tiles. Used with a Dremel oscillating tool. But I should have purchased a second set as these dulled pretty quickly and I had to spend 2x to purchase another one at a DIY store.

It definitely didn’t work as advertised! If your attempting to remove grout don’t use this

Worked to open up a junction box location in a plastered wall to install a larger old work junction box. Installed quickly on my Milwaukee M18 fuel oscillating multi tool

マキタで使用。コンクリートブロック目地を切断。 固めの砂利も多かったが特に問題なし。 当たり前だが木材のようにスパスパ切れたりはしないが、 これ以上は対象の材質とマルチツールの性能であって刃の問題ではないだろう。

ha llegado en perfecto estado y embalado

Usati per rifare le fughe alle piastrelle e fanno bene il loro lavoro... durata nella media se usate bene. Non vanno bene per tagliare piastrelle, per quello è meglio usare il flessibile col disco diamantato... Ottime sugli angoli.

Doet wat het moet doen, zeer goede kwaliteit!

The blades worked well with my Black and Decker multitool without the adapter so very pleased . I removed three tiles with easy with one blade and there is plenty of life left in it . I even cut a tile ( albeit slow and steady ) around an electrical socket . Only negative is the half moon blade is quite small , great for cutting the tile but bit too short for getting into the grout edges . Still good set of blades for price - would recommend them . Blade quality: Sturdy