VEVORStainless Steel Prep Table, 24 x 15 x 35 Inch, 440lbs Load Capacity Heavy Duty Metal Worktable with Backsplash Adjustable Undershelf & 4 Casters, Commercial Workstation for Kitchen Restaurant

From the picture this looks like a sturdy item you'd find in a workshop, lab, or professional kitchen. In fact it's somewhat flimsy, with the surfaces and tubes of stainless steel made from the thinnest possible sheets. The two leg tubes fit together with friction holding them—or not; one bottom leg piece fell out when I flipped the table upright. "Heavy Duty" in the item description seems like an overstatement.However, I'm giving it five stars because it's working perfectly for me. I removed an old electric range from an ADU and wanted to replace it with inexpensive counter space. This table is exactly the right size to replace an in-counter appliance and looks terrific when installed. I put a mini-fridge underneath it (clearance 33" with table feet extended), so I didn't use the lower shelf piece. The tight spot I squeezed it into provides ample stability for the table.Easy assembly; by far the most difficult part was peeling the protective plastic sheet that covers the top surface (hard to get an edge to start with).I'm not sure this would be suitable as a high-usage kitchen table in a freestanding location. Would probably be OK for infrequent usage, placed in a corner for more stability.

I like it alot but I think the company needs to put the directions for putting it together in with the screws cause I took out the table and never saw instructions until I went to throw the box away so I figured out how to put it together without instructions.Over all it's very nice and well packaged to protect table .Note taking the tape protector off the tops of table tiers took the longest .

Not only did the pieces not even fit together, but the pieces that arrive aren't even finished. Very small tack welds hold this thing together and there are sharp edges and burrs everywhere. It's a travesty that any company would produce a product this dangerous.

The media could not be loaded. This table is affordable, but mid to low quality. The metal is very thin, but it is not flimsy. The welds are spray painted silver. The shelf and table top bolt into the legs, but the legs do not bolt to each other, they stay together via gravity. I think this table is find for light duty garage or hobby work, but for serious business I would be cautious. The table does have some tape\film to protect the surface but it doesn't cover the whole top, and mine had some cuts in it anyway. This did not bother me for what I'm using it for, your needs might be different. It isn't a bad table, just have realistic expectations.

Perfect for my garage , and engine porsche parts ..

I didn’t read carefully enough— no casters included. I did my Amazon search “with castors” and as usual you get everything with and without. A bigger frustration? I asked the community what castors would fit so I could buy them. Not one person actually answered the question. Lots of “advice” on quality; or “it should be included” ( its not). If you can’t answer the question why do you respond? For the money, the quality is pretty good. Its not a rolled edge but people consider the price. It was easy to assemble. Just no casters. Would be nice if the vender offered the right size casters as an add on.

Very misleading description in the headline for this table, it says for Commercial Workstation for Kitchen Restaurant. In the photo, it might look like one, but this would not last a day in a real commercial kitchen.As other comments have stated, this unit is paper thin, if you were to put your foot on the bottom shelf, say like to tie your shoe, it will fold in half. There were several super sharp spots that could cut someone easily, I had to file a lot of spots, even one of the welds had a very sharp edge, and one weld was bad, it didn't even hold the 2 edges together, all of the weld was on one side of the joint. The legs were so thin, when I squeezed them between my thumb and finger, they bent! Sadly, you can't actually use the nuts on the wheels to tighten them down, as they are recessed in the legs, but I doubt you could tighten them before it would start spinning in the leg. While trying to remove the protective plastic wrap, all under the bottom of the tabletop, it looks like it was painted with silver paint, which did not dry, and everywhere I touched it, it stuck to my fingers/hand. After you put this together, if you try to lift up the table, the legs fall apart. If you have employees or kids, this is not for you! While it did come with a 5mm hex key to tighten the bolts, you will need a 12mm wrench/socket or some pliers to hold the nuts on the bottom shelf. The headline should be corrected to say, for very light duty.

The tables are easy to assemble but the plastic protecting cover was very difficult to remove. The seller should consider looking for an alternative solution to protect the metal. It drove me nuts!

The metal on the so called backboard ,was so sharp no burr clean off .I had to take a file to it to smooth off but the point on top if ra. Into it you would cut self bad .No good for what I wanted for but will have to keep I put it together. So not very good product.

Perfect just what I wanted.Best table ever!!

I found the assembly instruction images a bit hard to see, but the table is a nice solid table and rolls very easy.

I purchased this table to keep a hobard slicer in a residential kitchen. The table comes well packaged in a manner that would guarantee its survival in the shipping world. From the description I believed the table to be of a heavier gage and capable of withstanding the rigors of a home kitchen. the table assembled easily, and looked ok, upon closer inspection the surface was scraped and dented presumably from the packaging process. The table is under whelming, very light gage even for a home kitchen, susceptible to bending, denting and rattling with a mixer or slicer. It is not a NSF rated table and only appears to be of industrial quality, the wheels are a nice feature but the unit is hardly sturdy enough to use it with the rated weight on a tiled floor. To reiterate, very light gage, sharp edges poorly finished, may not last for any continuous use, great for very light use as a food or plate cart that remains stationary.

This table is ok for the money but wrongly discribed.The table will not hold the weight they say. The wheels buckled with only 70kg on it. Wheels are strong but the wheel inserts are only plastic. Complained to seller but no response. Bad service.