Kingroon PLA 3D Printer Filament, Dimensional Accuracy +/- 0.02 mm, 1 kg Spool(2.2lbs), 1.75 mm,White

I am still on the fence about this brand of filament.When I ordered this 4 pack (black, white, gray, and red) I only received three colors (the red was missing). I reached out to the seller hoping they would send the red, but instead they ended up refunding me for the missing spool. Honest mistake, with an honest correction so I am not faulting them for that.The matte finish is really nice and the colors are pretty much spot on to the picture.Print quality is usually pretty good. I have had a few parts that ended up kind of "meh" but that could be due to a nozzle that is wearing out.Bed adhesion is the biggest downside to this filament. It's not horrible but it is not consistent. Of course, slicer settings can be a big part of this, however, I have other brands of filaments they stick to my bed just great with the same slicer settings. I just replaced my print bed a couple of days ago, and my first print with this filament turned into a bird's nest of plastic :-). So, I reset everything and tried again (insanity principal) and then it stuck (with the same gcode file).

After seeing other reviews, I decided to give this brand a shot. My ender 3 pro likes it, and print quality is up there with more expensive brands like hatchbox.However-it started unspooling erratically while feeding. I relocated my spool holder, didn't help. In my picture, you can see where I had to re-wrap several circumference worth where it had unwrapped itself. You can also see my janky as hell flap 'solution' to keep the filament on the roll.The price is good enough that I'll keep buying it as long as print quality remains high, but it'd sure be nice not to have to fashion something so it'll come off the roll cleanly.

This PLA filament exceeded my expectations for its low price point. It came in a vacuum-sealed bag with a desiccant pack. I printed some miniatures and I didn't have any trouble with adhesion, even with some really tiny prints. I like the color and it's a nice addition to my collection.However, after using the filament for a while, I observed that it seemed a bit brittle and I was encountering a more stringing. I dried it for a few hours and the print quality improved dramatically (whatever method you have should work, I used a filament drier but food dehydrators or even your printer itself can work if you are careful).I would recommend this filament to anyone looking for PLA at a reasonable price, but as with any filament it will probably be at its best after drying it for a while.

I recommend this filament. With that said I rebought the blue and it’s a slightly different shade and it’s just enough to irk me. The first roll was a deep shiny blue and this feels more matte and less saturated. Still looks great but I wish the color hadn’t changed. I know it’s minor but what I’m printing looks better with that darker shiny blue.

Be warned that even though this is a great price, you get what you paid for. Most of the colors are fine, except for a few. Specifically the yellow filament roll I got was VERY inconsistent - the diameter was not consistent and therefore the quality of the prints, specifically the tolerances, were not consistent. But other colors were very consistent. From my experience, 2 to 3 rolls were inconsistent out of the 10 rolls. So still not bad in terms of cost vs quality.

The old review below---Kingroon reached out and resolved my issue. Great company behind their product. They responded in 24 hours with a resolution.________________________________________________________________________The black and grey spools have been decent. The white spool has clogged on just about every print.The picture above shows the failed print 9 hours in. The walls and infill for the last 1/2 inch is under extruded and stringy like I expect to see if the spool had a tangle. I'm not sure I've gotten a single print on any of my 3 printers that didn't do something like this with the white filament only. Huge waste of time and money. I've got half a roll left and I just threw it in the trash.I won't be buying Kingroon filament again. Back to Solutech3D for consistent quality.

Everything and anything prints like a charm with this material. 3 different kinds of 3d printers and still POOPS out PERFECT PRINTS. HIGHLY HIGHLY RECOMMEND. This is not like every other shitty Chinese PLASTIC. These are less expensive and have 100% success rate!!! Perfect everytime see for yourself.

i was surprised at how good this filament actually was , when you consider the price it was a good deal... but i only saw white and one other color .. but all in all a good buy. i didn't have any adhesion problems or any clogging problems . it ran nice .

The media could not be loaded.  Buen filamento, bien embobinado sin fallas, la aderencia falla un poco pero es más cuestión de la temperatura del cuarto donde se imprime, se arregla fácil poniendo la opción de barca en el laminador, yo imprimo a la temperatura de fábrica 200 boquilla y 60 cama y hasta ahora perfecto, recomiendo que si hay mucha variación de temperatura donde está tu impresora agregar un poco de laca, imprimo con una ender 3 pro y sin problemas :)Bastante satisfecho con el filamento

The media could not be loaded.  I'm on day 2 of a 3 day print and it's been printing flawlessly. It is a nice shade of white and value is unbeatable! I will be ordering more soon!

el filamento color gris tiene mala adhesion de capas, pero no genera hilos(estando bien seco el filamento), el de color negro se adhieren bien las capas pero siempre genera hilos a pesar de estar bien seco el filamento

Sin problemas para trabajar, buena adherencia, probado en distintas máquinas y con ninguna tuve algún contratiempo

generalmente compro esta marca por que me han gustado mucho otros carretes, pero específicamente este me salio de mala calidad, es casi un atasco seguro al usarlo, es quebradizo y poco fiable, nuevamente aclaro, este color en especial, por que en otros colores, Kingroon es de mis marcas preferidas en precio/calidad.