3 x Saxton 35mm Carbide End Cut Blade Fein Multimaster Bosch Makita Oscillating Multitool

Bought a pack of these to use on my Lidl Parkside Multi tool. They fit perfectly and work flawlessly. I am in the process of adding/ relocating wall sockets and these fitted the bill perfectly. Gone are the days of a club hammer and chisel and hello to the 21st century :) Used these to cut out the outlines of six sockets and cable runs , I used one so far to do the lot and tho` there is a bit of wear on that one blade it still works excellently after six sockets. The blade cut through the plasterwork extremely easily and then through the brick/ mortar (albeit a little slower , my choice) All I had to do to finish the job was use my SDS drill / chisel attachment to clean/level the bottom of the sockets as they need to be level :) Anywhoo folks, these are great blades and if used correctly (Slowly and carefully) they will be a welcome addition to any tool kit. Great product and a good price :) Keep the speed/ pressure down and you will be pleasantly surprised at how good they are folks :) :) Bald Eagle :)

Great product - Did exactly what I needed and saved me getting/renting an SDS Drill for what was always going to be a small job. Cut through 1940's red brick similarly to a wood bit cutting through timber joists. Made clean cuts at 3mm width. (Job: Installation of 25mm deep back box and chase) Wanted to leave a review as I was impressed. 4 Stars only as the one blade I've used has dulled enough to not be as effective upon next use - but it will still work. Highly recommended if you're looking for a 1 time solution and don't want to spend alot.

Amazingly- does exactly what it says, quick and shark - and quite long lasting. Great for cutting out electrical back boxes in blocks or bricks

Good initially but wear out quickly. only good for small quick jobs

Pros: Perfect, as they say, for chasing into plaster - through my skim and mortar with no sweat; Much less dust than angle grinder. Cons: Harder concrete (e.g. containing aggregate, blocks) wears blades out quickly, as you might expect; Still got fine coat of dust in room. Dust particularly bad when cutting through skim plaster. I had an empty room so just needed to seal one door with masking tape to protect rest of house. Haven't tried connecting vacuum to multi-tool yet. Anyway the tool does what they say - I'm very happy and ordering more.

Does not work with Bosch multi tools as advertised. The stamping for the blade is flat and does not fit into Bosch’s recessed star lock system. Do not buy if you have a Bosch multitool

... like cutting plaster board, cutting block work, trimming block work, chasing plaster, filing, etc etc etc. The only problem is they seem to wear at the tip quite quickly. I've had a carbon sanding block for years that has filed everything (tiles, timber, metal) and is still going strong. Maybe it's the speed at which these work? Anyway, for certain jobs they are great and accurate to use. I even managed to fit a dry lining box to a plastered wall by filing out a step in the plaster to accept the flange. It only took a couple of mins and looks like it was fitted before the plaster was added. UPDATE - Just ordered more. I used one to remove some very recalcitrant plaster that refused to come away from one wall of a bathroom (the walls others came away easily??). Performed without problems. The grit is quite coarse and does not wear away when cutting plaster. The original job I used them for was cutting block to insert back boxes so the tips wore away more quickly. Still, they do such a great job for cutting out for back boxes that it's worth the expense... look at the cost as "disposable", like screws or nails?

I had to return these blades as they did not fit my multitool so returned them and ordered correct chuck fit, my mistake

Sehr zu empfehlen, hab damit Putz durchschnitten, ging wie durch Butter, teilweise sogar durch Beton, auch wenig Verschleiß

durch ytong schneidet der aufsatz wie durch (sehr stark staubende) butter, bei beton war jedoch nicht zu machen, auch nicht mit geduld und Kraft etc.

Ich habe eine Multi Funktions Maschine, mit der auch sehr schwierige Arbeiten erledigt werden können. Preis Leistungsverhältnis sehr gut. Wird weiterempfohlen

Vorsicht! Das Produkt ist entgegen der Beschreibung nicht mit Bosch Multifunktionswerkzeug kompatibel (z.B. PMF 350)

Habe schon bei über 10 Fliesen die Fugen ausgefräst ging wunderbar einfach und schnell