Epoxy Resin Kit 64 Oz-Crystal Clear, UV Resistant, Self Leveling, Food Safe for Table Top, Arts & Crafts, Wood Casting, Jewelry Making, Use with Mica Powder, Silicone Molds, Alcohol Ink

So I have been wanting Epoxy the top of my bar for some time. I have been saving ticket stubs to events I have attended for over 35 years. So, the last thing I wanted to do was screw this up. I read the reviews for LOTS of different products. What I found most helpful was reading about other peoples experiences with the product. Especially people who had never done this before. Therefore, I am going to go ahead and add to the product knowledge of this epoxy.First, I will say what many other posts said - FOLLOW THE DIRECTIONS. If you take short cut, you are going to pay the price. Your epoxy won't set or you will have other issues. So let's start with the mix. I did what everyone else had recommended. I affixed my ticket stubs to my bar counter tops. Now I should also mention this. I have a high counter top and a low counter top. I did a test run on my low counter top. On the lower counter top, I had taken CD jewel case covers (i had hundreds) and affixed them and did the same process. This was my test run. It did not turn out perfect. However, the imperfections were 100% MY FAULT. I read some 2 and 3 star ratings and looking back on them now, I would venture to say a lot of the screw ups I read were user error. Not trying to be hard on the DIY user, but much of the complaints I read were user screw ups. My test runs had issues because I didn't anticipate a lot of things. Now back to the mix. First, don't go cheap. Use a two new containers EVERY TIME you do a mix. My counter top was big - 2' x 10'. When I did my first test, I did it with a quart plastic mixing container. That would have taken me all night. I quickly switched to a 5 quart bucket. Get the ones that have the ounces marked on the side. I mixed batches 64 oz at a time. I did just like it said. Mix for 5 minutes and then transfer to a second - clean container and mix for 3 minutes. I just used Alexa for this part. About the mixing - this stuff is hard to mix together. I did my first batch or two with a paint stick. Eight minutes of that is brutal. I read a review with a guy who had used a paddle paint mixer on a drill. So, I decided to give it a try. First time, I screwed up. I thought use a high speed - full trigger - and get it mixed good. That was stupid. Just creates one big air bubble - actually thousands that make the mix look like milk. i was able to use a heat gun to get the bubble out. However, it took forever!!!! Second time, I just pulled the trigger until the paddle started spinning - lowest setting possible. I just moved it around and reversed the paddle every couple of minutes. Worked great. I don't think it came out with any more bubbles and they came out easily.Pouring the mixture was something most people didn't really talk about. When you do your seal coat, you can move it around with a blade. Be gentle or you will create valleys. Now on the flood coat, no one ever said to move the product around. The indication is that it is self-leveling. I would say that is accurate to a point. If you just pour it and let it run, it is going to stay really thick - between 3/8 inch and 1/2 inch. I didn't want it that thick. So, just like the seal coat, I moved it around again with a blade. I just used a 6 inch putty knife. This stuff is STICKY. I bought a 40 pack of rags from Home Depot and a gallon of denatured alcohol. I used this stuff a lot to wipe things off and clean up my putty knife. Once I poured out all the product on the bar top, I just worked it around making sure I got it up tight in the corners. I does self-level and it was just a thinner coat than the 1/2 inch.I used a heat gun to get out bubbles once I poured the epoxy out. I liked the gun because mine has a fan, think hairdryer, and covered more area. The bubbles come right out. It was a very easy process. However, don't do it once and leave it. You will get sneaky ones that creep up out of no where. I went back and checked it every 30 minutes for the first two hours of dry time.Ok, last couple of items. First, temperature - I kept the temp in my basement between 70 & 75 the entire time. Do what they say and don't let it go below 70. This will screw with the curing process. The final thing I would say is this. Once you have mixed it, the consistency is like thick honey. My bar is 3/4 inch laminated oak plywood. I have taken a piece of 1"x3" and made a half inch dado cut and used this trim piece to cover the edge of the ply wood. It fit really snug. I thought there was no way this was going to seep in, behind, down, and then back out of that piece of trim. Well, it did in a couple of places. if I was doing this again, I would run a bead of caulk on the under side of the bar to prevent those drips from happening. I was able to wipe it all up and keep the underside wiped down, but I had to do this for like two hours until the product got thick enough it no longer seeped out.Ok, sorry this is so long. But, i found the long review really helpful as I planned my project. I used two of the two gallon kits to do my upper and lower bar. Keep your environment as dust free as possible. Little threads and dust particles will get on the top and there is nothing you can do. This includes shutting heat vents in ceiling that are close to bar (learned that on my lower top.) . Final comment - TAKE YOUR TIME. This is not a go fast process. You have to be willing to go slow and be patient. I included a couple of pictures of the finished product. Love the way it turned out.

I have been using another brand in my shop for years and reached out to try this product as a more economical alternative. It performs well within all areas and i will continue use it.

The media could not be loaded. My husband bought this to use on a table that he made and it turned out really well. He technically gave it a "4.5" out of 5, but I rounded up.It takes 72 hours to fully harden, it dried quickly, but had that feeling of nail polish when you first leave the salon, "dry but could still smudge" until the 72 hours. But now it feels great and looks great. The only thing my husband said to mention was to MAKE SURE YOU HAVE A LARGE GOOD-WORKING HEAT TORCH.He only had a very small one, okay, technically it was a lighter, and because of this, we do have a few small bubbles, but you have to look closely to see them. (And this is user-error. He attempted to use my hair dryer too, but it was a dyson, and he abandoned that quickly)It still worked, and looks better than others he has used before. I love how great it looks with the wood grains, the perfect gloss.The hubs said it's for sure a repurchase for future projects...along with the torch.

I bought this table top epoxy to do a table. It worked great! Follow the instructions and all should go well! The first photo is after it cured. I was clear and no bubbles! I was excited! So after full cure, I used it outside for a party. Well that’s where I went wrong. The 2nd photo shows how it yellowed in 1 day! So I looked it up and there is not UV protection!! 😩 So that’s on me for not researching that further. I just went by what other reviews and they said how well it worked and I follow an artist that promotes this brand, so I thought I would give it a go. Yes, it worked well, but why would Promise Epoxy not add UV protection to all their epoxies??

The best quality resin I've ever used. I feel that the value for the money is worth it. If you get bubbles its based on how you mix, not the resin quality. The cure time was fine. I dont see any yellowing.