QualGear Pro-AV QG-KIT-CA-3IN-W Projector Mount Kit Accessory Single Joist Ceiling Adapter, 3" 1.5", White

I was having a hard time finding a mount that would work with the Epson 5030UB as its mounting screws are very far apart but this mount was so versatile I had no problem adjusting the arms to fit the large projector. I especially like the Mounting Bracket cover which hides the bracket attached to our wood beam ceiling. The tube was just large enough to run and conceal the power cable and the HDMI cable.The Adjustment options were also nice including tilt forward and back and side to side. I purchased the optional pipes to make the drop from the ceiling almost 14 inches. The appropriate height for the height of my screen location.It comes with logo stickers on the pipe and the bracket cover but I was able to easily remove these branding stickers, making the unit look clean and modern.Its solid and comes with additional small screws to lock in the drop pipe so it doesnt turn left or right. Mounting the projector bracket to the pole was easy based on the design. I was able to lock all the screws down and everything is snug, I dont have to worry about the projector moving in the future and this is important as I spent a bit of time aligning the projector image perfectly to the edges of my 127" screen.It was a bit pricey compared to the other options, but I'll gladly pay a bit more for functionality, compatibility, stability and build quality. This met all my expectations.

I made a rookie mistake when preparing the area where my new projector would end up hanging from the ceiling - I measured from the CENTER of the projector instead of where the lens would be. That made the projection a few inches smaller than I wanted. (I also mounted it a foot closer to the wall than I should have, but that's another story.) Easy fix with this mounting bracket! I just adjusted all the brackets to push the projector as far back from the center as I could.Major kudos to the engineers for making this so easy to use and install as well. I thought I was going to need one person to hold and another to tighten, and I was wrong. Loosen one screw, then you can pull the entire bottom part of the bracket and projector out together very easily by yourself. Bravo!

Very nice, physically strong design. We adjusted/re-adjusted the the projector mount component such that it was fairly balanced with respect the down pipe. (This turned out to not be as necessary because the base secured very nicely to the ceiling. ) Possible to order/get longer down pipes. Cords and cable run through the down pipe for a nice clean finish.

Not the best designed channels, it does get in a way to make forward and backward adjustments requiring you to remove the entire projector and re-mount if mistake is made in the initial mount. I suggest getting their other model that's meant from drop ceiling for more flexibility albeit they cost bit more and I wish I had seen those first.1.5" inch pipe can be shorter if the ceiling clearance is low in the area where it's installed, our ceiling is only 8' so I replaced it with Anvil 8700143350, Steel Pipe Fitting, Nipple, 1-1/2" NPT Male x 2-1/2" Length, Black FinishInstalling shorter pipe makes the adjustments bit difficult for some screws and you will need to be creative. I shaved off 2.5'" of pipe in my installation so we can install a larger projector screen for UST projector.Definitely like the ease of unmounting and mounting feature, I had to remove and re-mount the projector 4 times and I could do it by myself installing 27 lbs Epson UST projector.Only gripe is the channel design that limits forward and backward movement so double check and ensure your projector is center loaded because if the projector moves too forward or backwards and not center mounted then the channels will droop in front/rear causing your projector to be slightly tilted and that may require more tweaks to get it perfectly horizontal from all the sides.

I was looking a flat ceiling mount that I can install for my 26 lb Epson 4010 projector. Glad I bought this product over a bunch of cheaper versions out there. This product is very sturdy, with easy installation setup, and clear instructions, it took just an hour to install. The best part is it comes with 4'' x 2'' plate that would easily fit wooden joist beam (which is a big plus over 4' x 4' base plate installation). Just takes 2 solid bolts that would go in joist. There is a paper stencil that was handy to mark and install plate. Once base plate is installed, the rest of assembly was a breeze.The mount is very sturdy, good heavy metal to hold project weight. The top adjustments was easy to manipulate tilt to get a straight projected picture. Once mounted projector can be rotated 360 degrees. The cover over base plate worked out well to hide hdmi and power cables, it is not too big though, there is a decent space between projector and mount, that worked out to conceal cables.Overall it seems to be very sturdy projector mount.

Works great. Easy to install - incredibly sturdy. All kinds of axis adjustments are possible. The telescoping arms can accommodate a wide range of projectors. Installation instructions were easy to follow. All of the miscellaneous hardware was bagged and tagged and easy to ID. Solid construction. Would order another in a heartbeat.

Its a great quality and well built product.I have a 28lb projector and needed a sturdy projector mount. This definitely is highly recommended to go for. I has great flexibility in terms of compatible to projector sizes, (extensions), rotation, etc.The very fundamental is its strong and sturdy... so one for the lifetime. Highly recommended.In my case I would appreciate the Amazon customer support for their considerations towards my request to expedite the delivery for free of cost. I had the person coming over to mount this and i requested for an expedite in delivery.... they made it happen. Thank you for that.