Edge Supply Walnut 24 x 48-inch Flat Cut, 3M Peel and Stick Wood Veneer Sheet – Self-Adhesive Wood Veneer, A Grade, Smooth-Finished – Versatile for Furniture Restoration, Cabinetry & DIY Use

This is one of my best buys from Amazon! Absolutely beautiful Mahogany veneer that is extremly easy to use and stain. I needed to replaced the veneer fronts of two antique dresser drawers. The cost of having an antique repair shop do them was prohibitive, so after watching a few You Tube videos, I decided to see if I could do them myself and ordered the veneer from Amazon. I was thrilled to open the box and see the quality... the wood grain of the mahogany veneer is beautiful and it was very easy to apply. I do suggest watching a You Tube video, it helped. The drawers came out better than I could have imagined and they look exactly like (if not better than) the original veneer on the remaining two drawer fronts. Very easy to sand and stain.

Great product, easy to work with and much better than expected.

Excellent product. Came just as advertised. Others who say it didn’t adhere don’t know how to use the product. This stuff sticks perfectly. The wood veneer is beautiful.

This stuff is great. Used it to renew the cabinetry in a campervan conversion. It's so thick that it hides any blemishes (like raised screwholes, etc.) in the surface it's adhered to. It took "dark walnut" colored Danish oil beautifully, and was finished with a coat of beeswax. I started with one roll and ended up ordering many more. My only grip is that the adhesive doesn't extend all the way down to the cut edge (which is exactly where it's needed the most). There is a centimeter or two strip along the edge without adhesive.

This veneer was used on the riser of my little stairway that enters into my music room. It’s really sort of like a stage. I was refinishing my wood floors, and the riser could not be re-used, so this veneer seemed appropriate. We stuck it onto the plywood underneath, and stained and finished it with Minwax Classic Gray, like we used on the rest of my red oak flooring, and it is beautiful! It worked perfectly. OK, so it can’t be sanded and refinished in the future, but I’ll just purchase more veneer if I need it :).

Ruined a vintage china cabinet that I was restoring. I properly prepped and cleaned all surfaces and used a j roller to press the veneer on. I relaxed the veneer ahead of time and acclimated the furniture and veneer in the same space for 2 days before installation. I’m so mad about the time I’m going to have to spend to peel the veneer off and see if any of it is salvageable. I was in the fence about using adhesive backed and I should have gone with a separate glue down veneer. I’ve lost days worth of time due to this mistake of a purchase.

I’ve ordered this walnut edge banding twice and have been impressed with the quality. The grain pattern is consistent with natural variations, and the veneer is thick enough for minor sanding if needed. It’s easy to apply with a standard iron (cotton setting works well) and adheres strongly across surfaces like plywood and deglossed laminate. Just be careful not to overheat, as it can cause the adhesive to run slightly. Durability has been excellent with no peeling or lifting, even on multiple projects. For trimming, both manual edge trimmers and a router with a high-quality flush trim bit work smoothly. The product is versatile for furniture projects, and even beginner woodworkers will find it straightforward to use. My tip for best results: ensure the surface is well-prepped and dust-free to maximize hold.

Easy to work with and packaged well, but the pressure marks ruined the finished look of my project. I’ve invested too much time and money into it at this point to start over. After sanding for days, carefully avoiding burn-through on the veneer, the wood looked significantly lighter—until I applied the finish, which made the defects “pop,” and not in a good way. My project is a very expensive antique, so I have no choice but to live with it, but I wanted to make others aware. Unfortunately, I only just found the other reviews from people experiencing the same issue.

I was very disappointed when I opened the package up. The 3 strips that made up the full width of the roll were dramatically different in colour, with the centre strip being much lighter than the two outside strips. I had 3 sides of a floating mantle to veneer, and ended up wasting a lot of an overpriced roll to scrape together a finished product. If the timeline hadn’t been so tight to meet the clients deadline, I definitely would have returned. Another issue was a series of bark inclusions on one end of the roll. The quality was on par with something from a box box building store, but definitely not up to a standard for something priced over $120 CAD.

Se travaillle tres bien