Aardvark Minoura CS-500 Headset Spacer Mount Accessory Holder | bike-handlebars

Great little gadget. I've paired it with a Cygolite Metro in a configuration below the bars. Over ten miles of fast singletrack on a mountain bike, neither budged an iota. It doesn't clutter the bars or look kludgey like many alternatives, nor is it limited to mounting Garmins.I did run into a few complications with my full-suspension rig. It was a bit tricky to align in combination with the expanding nut that holds my steer-tube in place. I also discovered that the cross-bar I use to hang the bike from a trunk rack won't fit with the Minoura in place, so this $15 device prompted a $200 hitch-rack purchase I've been putting off for six months. Expensive hobby, this.

This works great on my seatpost, (but I don't think it will work on 'aero'-style seatposts) I got this since I wanted a rear 1200 lumen taillight on my bike, and got the "1200LM 3 Modes CREE 5V XML-T6 USB LED Headlamp..." sold here on Amazon.com to use it with, thinking my "Kmashi 10,000maH" external battery pack would work for it, but either I got a bad one, or the overvoltage sensor in the light, or the battery pack keeps tripping. ANYWAY, back to the subject. I said it fit on my seatpost, (but had to remove it first [piece of advice, mark where your seatpost is with a paint pen or something before you remove it) Once I did, it fit quite well, as will MOST seatposts, however, to make it a bit larger, loosen the bolts by the seatpost/headset spacer mount, then you can tighten them once it's on. The bolts require an 'Allen' wrench (not sure what size, though) and the mount (which can only accept one accessory) has about the outside diameter of a 25.4mm bar.

Although the item was built for rugged activity the piece that mounts to the trike was too small for the boom of the trike and, therefore, not usable.

This was the perfect adapter to mount the headlight on my recumbent trike. Since it is adjustable, it works well to mount the headlight on the stalk sticking upright of the main frame of a trike. So far, it seems sturdy and we have had no issues. Purchased two of these units.

Excellent light mount, eliminates the need to mount your light on your handle bars giving the bike a much less cluttered look and far more practical since the light sits right above your front wheel dead center.

This mount is a great design and is well made from high quality materials. It could be the perfect mount if it only fit. It says it fits bars 1 1/8 in diameter. My bar diameter is 1 1/8 and this mount just would not go on. So close, but not a winner. I returned this mount and went with a different one.

No guess work on this item well made and easy to use. All the bicycle items from minora are made for heavy use try the bottle holder i have one on the handlebar for easy reach on my touring bicycle.

Only big enough for one item, but does a great job at it. I have a rigid for mountain bike set up with wide diameter cyclocross (road style) bars on it. My light wouldn't fit any other way. Seems solid. Glad I bought it.

Aside from adding extra space for accessories (action cam, lites, etc.) this also works as a spacer ring for the steering tube. The part is reasonably light and rigid when installed properly.

I was a little dubious about this things rigidity and suspected it might droop if provoked. Proven wrong on both counts, light hasn't moved at all.

ライトはセンターに置きたい。キャリパーブレーキに取り付けるステーはなんか怖い。で、これを選んだがとてもよい。思ってるよりも目立たない。「そういうライトなんだな」という程度に見える。

Fast delivery. Good quality.

Für Rennräder ein muss!Die typischen Rennradlenker bieten nicht gerade viel Platz für Zubehörteile. Besonders Fahradlampen nehmen dort den meisten Platz ein und sehen durch ihre meist klobige Bauform am Rennradlenker besonders blöd aus. Zudem gefällt mir ohnehin die dezentrale Position einer Lampe am Fahradlenker nicht.Ich habe daher nach Alternativen für mein neues Cyclocross- Rad gesucht und bin mit diesem Halter für 1 1/8 Ahead fündig geworden.Um den Halter zu installieren musste der Lenker samt Vorbau vom Gabelschaft abmontiert werden, der Halter ersetzte dabei einen Spacer von 10mm Höhe. Innerhalb von wenigen Minuten war der Halter montiert und ausgerichtet.Das Ergebnis überzeugt mich vollkommen. Meine Lampe integriert sich jetzt nahezu perfekt und zentral ins Gesamtbild des Rades.Der Halter ist gut verarbeitet und das zu einem top Preis. 5 Sterne und eine absolute Kaufempfehlung.