Nilight 90025B Led Light Bar Mounting Brackets 2pcs Universal Hood Led Work Light led Pods Mount Bracket Clamp Holder for SUV Truck Off Road Installed No Need Drilling, 2 Years Warranty,Black

I honestly did not have high expectations, but wow, these have held up so far. They didn't work where I originally wanted them to on my Uforce 1000,but they did work for a 20' light bar on the back of the roof. I did not expect them to hold the weight of the light bar, but 3 days of off road trail riding it has not budged. Very impressive. No drilling into anything.

I like how low profile these are compared to most others. They were easy to install and seem to be pretty sturdy. Good value as well.

I bought these alongside the Nilight 2pcs 60w 4inch LED pods. It was a fairly easy install aside from a little struggle to get all 5 screws tight at the same time. I got the light mounted on pretty easily too, I was able to use the same screw that came with it and it fit without the washer and seemed to get tight enough. The problem came when I tried to close my hood. Unfortunately, it wouldn't close all the way because the bottoms of the screws hit a plastic piece which runs the entire width of the hood to hold a rubber seal. It's a small gap and I didn't have any room to back the mount away from the edge either.Overall great product, just doesn't fit on my truck.

These mounts work great. I used them to mount a light bar to the bumper of my truck with no drilling required. I also used the mounts on my rear bumper to mount cube lights to it with no drilling.

Great concept but when I received my package with the brackets I was missing several of the small Allen head screws so the driver mount has 5 screws and the passenger mount has 2. The packaging needs to be sealed up on a bag not a thin box. Other than those issues the mounts look good.

Bro I put some cubes on these n clamped it to my hood. I be going 100+. maybe. And they hold on! Doesn’t move or anything. The baby screws u see at the bottom are there for u to screw them on tight. You have to make sure all of them are tight because they hold up a plate that’s used for the clamp. If the plate wasn’t there then you would leave holes on ur vehicle. It’s wonderful. Easy to instal n remove to move around. Ima buy more n use them to add more lights to my jeep instead of getting the bigger bulky brackets because those sometimes leave marks on my paint.

Great value, hold well, not old enough yet so see how the finish holds or if it rusts, look great

I purchased these mounting brackets to attach two fog/driving lights to my Mazda5 for additional lighting and better visibility in foggy conditions. I really had a good experience with Nilight products in the past and figured why take a chance when reviews on similar products complain about corrosion and mounts loosening up or detaching from vehicles.When I first mounted the bracket and attached the light, all was great and alignment looked doable. Drove 14 hours in the Thanksgiving rush to pick up my kid from school. Mount stayed secure but the center of the beam hit about 5-10 ft in front of the car. So the next day I went to adjust the light and realized I was at my light’s vertical limit so the slope of hood was too much for the pods. Not great but my fault not Nilight’s. I disassembled the mount and then my disappointment began.First, the knurled Allen head bolt to mount the light to the bracket went through the rubber pad and created a circular scratch through the clear coat and paint. This product clearly needs either something to limit or block the bolt from being driven beyond the upper metal bracket. This could easily be accomplished with another thin metal plate inside the rubber cover or fabricating the plate so the bolt bottoms out. Another fix is to press or weld a stud to the plate and use a nut to mount the light. Additionally, the lower plate actually created an indentation under my hood where it was secured.So overall, it’s easy to install, and holds a 4” pod very securely. Unfortunately, mounting options are limited to a nearly flat horizontal surface and may damage your vehicle’s finish. Now I get to go look for another mounting option and buy some touch up paint before it starts to form a layer of rust.