JetJRB-14 Riser Block Kit, 7/8" Guide Post (708717)

I wanted to upgrade my bandsaw for re-sawing and this kit did was an important part of the upgrade.It was easy to install and increased the re-sawing capabilities. Great purchase. I also added a re-saw fence. I’m almost done. I just need to add the quick change arm to make changing blades easy.

This is a great kit for the 1 hp Jet band saw. If you need the one for the 3/4 hp use: Jet 708717A Riser Block (search Amazon for 708113A. Factory Authorized Outlet was a great supplier- see below notes.)The only difference between the kits is the 1 HP kit has a thicker guide post and it does not fit the 3/4 HP band saw.If you get the wrong kit like I did, don't bother to call Jet - I had hoped to do a direct swap for the parts but their parts list didn't even have the right part numbers so the front desk couldn't help me. I waited for about 30 minutes for someone from tech support to answer questions about the guide post. They never answered and on a call-back, I couldn't get through.Because my Amazon search didn't pull up the correct kit (I guess I didn't have the right terms) I Googled and found it at FAO (I now see it listed on Amazon) and they sent it out immediately. Thank you FAO!The kit was easily installed and I love the increased capacity with the Laguna105" blade which cuts through 12" Maple with ease. 6" Riser Block for 708113A105" Laguna 3/4" Resaw King Carbide Bandsaw Blade

Had to enlarge one of the alignment holes slightly to allow pieces to fit together. Otherwise, everything seems to be working correctly.

...no matter where I looked, Including JET's own site, I could not come up with a listing of included parts, and the tiny picture of kit found on everyone's web site is nearly useless. Sure I trust JET -- but only to a point. For those like me who have modified their bandsaw with accessories like the Carter de-tensioner, or roller bearings, rest assured this kit will still fit, and you won't lose any functionality.The parts in my kit were as follows:1. Rear blade guard (metal, not the cheezy plastic that came with the saw)2. Longer v-grooved shaft for the front/upper blade guard, enabling your upper guides to extend all the way to the table-top. Read the instructions carefully to install this one, or you'll be chasing a very small ball-bearing around your shop.3. Front Blade Guard -- sheet metal, just like the original, but with an adjustable extension. Mine didn't quite fit the bolt holes, even on the OEM guide, but a couple passes with a file fixed it in short order.4. Cast Aluminum Riser Block and hold-down screw.5. 105" saw blade -- toss it out and buy a TimberWolf brand.Assembly was a snap. Mine went together in about 20 minutes. The hardest part was balancing the upper roller assembly while tightening the hold-down screw. Not really too big of an issue, but a third hand to hold the bolt steady while you hand-tighten the nut would be helpful. Alternately, you could do as I did and use a piece of tape on the bolt head to keep it from turning as you snug the nut.After it's all set according to included instructions, you may want to go one step further and tap a 10-32 hole in the back of the original lower cast aluminum bracket. It will allow you to re-use the original power cable loom (W shaped bracket) and thus keep the power cords from chafing on the lower blade door. The instructions don't call for this, but it's never a good idea to allow power cords to rub against sheet metal.

It works like I hoped it would. Lines up on the bandsaw well. I installed it myself but would definitely recommend getting one other person to help hold it in place, it's really too heavy for one person to both hold it and tighten the bolt. It would be easy to hurt yourself. I love it. It's nice to have the extra capacity.

Got this kit for a 1998 Sears Craftsman 14"Band saw , had to drill some new holes but can done not very Difficult . There are many how to Video On YouTube Make a template go slow . Great results Work s Beautifully.

I'd like to add something original but I think it's all been said. This is a very quick, very well-made, very accurate product that adds 6" to the saw.Some reviewers said that theirs didn't come with a 105" blade, mine did. It's good enough for me for now, I'm only sawing pine and basic stuff.The instructions are very clear but then again this is a pretty simple installation. A pre-drilled hole for the power cable would have been really cool, after all Jet pre-drilled the table for the fence/resaw guide (another product I bought and love).The hold-down bolt that connects the upper arm to the base is very big (nice!) but I only had to turn mine less than 1/4 turn before the upper arm tipped over. I was able to catch it before it crashed into the table but consider yourself warned.

I recently purchased a Jet 14 inch closed base bandsaw. It works great. Before I ordered any blades for it, I decided to get the Riser block first. The Riser block increases your cutting height from 6 to 12 inches. Your band saw blade size will then go from 93 1/2 inches to 105 inches. If you need this, get it before you buy any blades because your old blades will be too short. This is not an item that you can take off at any time. It is a permanent option. The Riser Block was very easy to install. You remove the big bolt that holds the top wheel support the the bottom and add the Riser block and use the new bolt to secure it. The kit comes with a metal rear blade guard. The one that came with my saw was plastic. The only tricky part was lifting off the upper wheel and reattaching it. Since it is fastened at the back, it wanted to tip forward. With me Riser installed, I can resaw fire wood and thick beams into boards. Think of all the flavors of wood you can now use for projects.

I installed this on my jet 14 '' bandsaw works well just installed had in box for long time .gives me re-saw capcity of almost 12''.