JOJOY LUX H11 H8 LED Low Beam Headlight Conversion Kits, Fog Driving Light Bulb Kit, H9 High Beam Bulbs, with 56W 6400LM Epistar LED Chips, 6500K Diamond White Color, 1 Pair

It's a shameBought two sets for my 2007 Mazda CX7 AWD and 2013 Mazdaspeed 3, two sets of H11 bulbs I bought (6000 kelvin) one of them failed after 3 hours of use... the light started to blink (could see on the median barrier of the road) and went dark... after examination one side was dead and the other chips were on very dim.I had to use a new bulb from the second set of H11 of the same brand, the ones intended for my other car, and it has worked quite well since. Around 30 hours of use, thru two heavy storms and at high weather temperatures and at high speeds (120+ mph)Other than the first bulb failing these are really good lights. My CX7 has already new 6000 Kelvin HID/Xenon lights (replacing the 4300 Kelvin OEM ones) and these H11 are exactly as bright as the HID: that means 3000+ Lumens, compared to the 3200 max from the HID.And with the adjustment feature one can not only adjust the sides of the bulb to point horizontally (the line holding the leds vertically) but also pulling it out a few millimeters to change the focus of the mirror of the fog light: this was increasing the light focus to point higher than just the intended rectangle. Fog is only a January/February thing were I live, and I am sure the correct bulb position would be all in, but driving at night it helps to increase the illuminated area as much as possible even if other drivers don't like it (KIA and Hyundai cars do this, among others so...)Quick note: installation of the fog bulbs can be achieved thru the fog light pocket itself, from the front of the fender... by removing the frame it leaves space to maneuver and change bulbs... and adjust the lamp as well.

These LED lights of size H8-H11-H9 are great replacement for the low beam bulb on Mazda 3, but you will have to take a slighlty different approach to get those fit properly.Starting on driver's side, remove the existing low beam bulb (the middle one, others are indicator and high beam). Press the notch on the electrical connector, from the bottom side furthest from the bulb, and pull apart the bulb plug from the socket. Compare the LED lights with the old bulb, and verify that new LED light is a good fit by inspecting the diameter of collar and spacing in the connectors.Be careful with the polarity, the +ve side on plug must connect to the red wire side on the socket.Insert the new LED lights into the hole, you will have to allign the 3 notches in the collar (1 big notch and 2 small notches). Do not press the blue back of fan, hold the black area around the fan instead. You will have to rotate the LED assembly by holding the collar to get a good fit. I found it impossible to rotate the assembly in that hole because of very tight space (passenger side bulb area has even tighter space). Therefore, I had to remove the collar (black with red-seal) ring out of the assembly, and only then I was able to insert/press/rotate in the hole. I then simply inserted the LED-fan assembly firmly through that ring. I even had to swap out the read washer from the old bulb to get a better fit on the passenger side bulb.Connect the new plug to the socket (keep in mind the polarity). Align the LEDs vertically by rotating the assembly as described in the manual. Turn the lights on to verify the functionality.

I got these to replace the Halogen bulbs in my 2018 Ford focus sedan. The first two pictures that I posted are the before and then the last two Are the after and the video. They are really bright considerably brighter than the halogen bulbs and for the price you can’t beat it. Thanks again for a great product

These work so much better then the last ones I ordered when the LED’s were all around the post. They have the ground covered like regular head lights. Just wish it was a little brighter.

The lights was really bright. It was really freaky though when installing it.. make sure the build area is not touching anything because it will create some smoke. Also when testing it make sure that you put it where the fan in the back can spin freely. Othe than that so far it's really nice..

I am sure these bulbs are great, but they did not fit my Land rover LR2 that was pretty frustrating when the description cites that they should.

Can't vouch for longevity, but super bright light and fits mazda cx 5. Definitely very white light with good distance.

Easy to install. Much brighter than original halogen bulbs. Am considering getting the high beam LED's to improve night time driving. Would buy again.