6amLifestyle Headphone Headset Holder with 2 Silicone Covers, Strong Adhesive Easy to Install, Aluminum Desk Dual Hanger Stand for PC Gaming Headphones Sennheiser Sony Bose Beats, Black (Patented)

Any old hook could keep my headphones off the ground, but this one is smart enough to also provide a wire keeper to help tidy up my workspace. I also like the fact that it is wide enough to make sure the ear pads don’t touch each other when I’m not listening at all. Strong adhesive and feels well made piece.

As others have noted, because the screw holes are directly above the horizontal "arms" that the headphones rest on, its difficult to mount. Once mounted, I don't have to worry about the adhesive wearing out over time (all adhesives do eventually), and I can pull on it with some force and it holds sturdy.I saw many products on Amazon that appear to be the same material, have the same description, etc. I purchased this one and one other to compare them. I chose to mount this one, because of the wire holders, which I never ended up using, and because of the extra space for holding headphones.What I did to mount:1. While sitting in my chair, position holder under desk, with headphones hanging, to a position I like. Mark vigorously with a pencil to mark the position of one side.2. Go under the desk, using the markings in Step 1, measure X inches in several areas along where the hanger will be mounted, to get a nice parallel mount. Connect the dots using a straight edge.3. Position holder along the marks I made in step 1 and step 2. Mark holes for drilling with pencil.4. Drill pilot holes in pencil marks with a 1/16'' bit.5. Remove adhesive backing from holder and position hanger lining up the holes on the holder with the pilot holes (this step was annoying given the holder blocking my light. Loosely attach holder to the bottom of desk.6. I initially tried using a drill, but I found that a skinny screwdriver, such as one from iFixIt, can turn the screws with less of an angle. Because of the pilot holes, I did not need to apply much force with the screwdriver to apply the screws. Because I ended up using a screw driver, it should be easy to use your sense of touch to just apply pressure to a screw and position the holder until you feel the pilot hole and then install.7. Viola, mounted holder.

Adhesive is good for most people, but I prefer a more permanent solution if possible. The trouble with this is that the screws are in such a place that it's hard to put them in without stripping them. If mounting permanently (with screws) be mindful of the following:1. Drill pilot holes. You'll need them. You WILL strip the screw if you don't do this.2. If you have a flex extension, use it. I used one from an iFixit kit, and it worked really well. If not, be very careful driving the screws in. Do not use a drill.

Its a headphone mount, it does indeed hold headphones. However if you have two i find it better to slide the cable on first and have the headphone near the end so the cups dont touch together. I cant speak for how good the adhesive is as i used the included screws

This is a great headphones hook, but is very difficult to use screws to attach since there are no pass-through holes for your screwdriver.I had a single lightweight headset (Logitech H570e) on just the adhesive for two months, but like other reviewers I doubt the adhesive material (it's almost a gel) would stand the test of time with the weight of two headsets on it. I tried a normal screwdriver at an angle, and ended up breaking the screw head. Ultimately I had to use a low-profile screwdriver (KAIFNT model K451; B07YCP213C) to get screws in.Other than that, it's fantastic. It has a nice look and texture, is strong (the metal part, not the adhesive), and comes with rubber end caps containing wire-management holes. I didn't initially find the wire management to be helpful since you have to take the headphones off over them, tangling the headset in the wire, but I've started looping the cable up through one hole and down through the other, with the slack all on the "down" side, and that seems to be working better.Overall: Four stars. Would have been an easy five if it weren't so difficult to attach the screws.

This quickly decluttered my desk and gave me a reliable place to hang my work and gaming headset when not in use. Multiple mounting options but the adhesive worked just fine for me.

Good item and it does what I need but I'm taking off a star because of the screw placement. I didn't realize it until I was installing the item to the bottom of my desk as a headset holder but the screw holes are parallel to the actually hook that juts out. So you basically have to screw this in from a slight angle because the metal hook is obstructing your way. You can also choose not use the screws and just use the adhesive so atleast you have that choice.

I was expecting a hanger that was a little larger. If you hang two headphones on the hanger the earpieces bump against each other and push each other outwards. The hanger should be wider to allow the headphones to rest straight down instead of being pushed out by one another.Aside from that you can see by the photos how big it is or I should say how small it is. It's OK but I'm going to still look for another one that's larger.

Extremely useful headphone hook that can accommodate 2 full-size head phones. The rubber tips are brilliant for cable management.I docked a star for the screw holes which are in-line with the rest of the hook. I couldn't put the screws in straight because the hooks are in the way. It was way harder than expected to mount and I just about stripped the screw heads. I'd like to see cutouts for a screwdriver to fit directly below the screw holes . If you use the included 2-sided tape, this won't affect you.

great product! strong adhesion no need for screws. I have a heavy set of hifiman headphones and a wireless pair of Sonys. mounted them under my desk now. Desk much cleaner. Great product

Installer depuis quelques mois et il tiens très bien ! Très bon produit

Easy to stick to under desk. I love the extra rubber extenders. I'm very happy with this product.

A lot smaller then the picture shows and the rubber ends were ripped out when I opened the box