【ALLOY UPGRADED】W10780045 WTW4816FW2 NTW4516FW2 NTW4605EW0 NTW4516FW1 WTW4800BQ1 Washer Suspension Rods Kit 4 Pcs by Beaquicy-Washer Parts for Whirlpool Kenmore Suspension Rods RTW4516FW1,11020102310

Worked great, my washers spin cycle is super quiet again. Very easy to install.

Our washing machine was a rocking and a knocking w/ a basic load. Enough to scare the daylights out of anyone who's intimidated. The machine has an agitator so to determine if it was the balance springs I just pushed down and released the agitator, and it bounced back w/an extra bounce. To solidify my finding I treated the agitator like a basketball dribble, and it bounced freely like a ball. Unacceptable!!! It shouldn't bounce and should have resistance on the BBall dribble. So, I ordered this set of balancing spring set after assuring I had the correct part number. ( FYI : Web site Parts select and or Parts direct for OEM number) The new set was longer around 1 3/4" and the new top mount ball joint or the socket didn't fit like the existing. (Made in China go figure) and the part number matched ..at least on the box label. Needless to say, for the hell of it I used the existing top mount and new longer springs. Brought it back into the house, had the wife load it up w/ some heavy stuff and it worked like a champ! Collectively the entire job took less than 1/2 hr. this includes pulling the machine and working on it in the garage. To get to the point for the price it was well worth it otherwise you'll be paying double if not more at your local appliance parts shop or one on the net and better yet than buying a new machine. Make note the extra length on the spring set did not affect the performance! Happy Wife Happy Life !

Scared me at first, Longer Rod, Socket too large for top hole. Have to leave old socket in the top, The Retainer is much thicker, which accommodates the Longer Rod. Works fine, they need to have correct Socket, and would be perfect. Would only be an issue if old socket was cracked or broken. Left arm above is old one, you can see it is shorter, but retainer is thicker. Also can see old socket fits in smaller hole. Works Perfect. 1) Remove Power, Hoses, and screws in back joining top and bottom. 2) Tape Lid Closed, pull Top forward, lift up, jiggle a little(the lid,Silly), till it lifts up. 3) grab a front rod about 8" down with good pliers or vice grips, lift up, remove retainer, release rod down. Do 2 front ones first, Don't release all 4 at once. 4) Tilt Machine forward, remove 2 Front Rods, insert new rods. Put back upright. 5) Grab Rod down low so you can pull through high enough to attach Retainer. 6) Do same for Rear. 7) Secure top, attach hoses, power, and drain. Tub shouldn't bounch like it did before(push down on center of tub to check bouncing) They won't(shouldn't bounce with the new ones) 4)

I was concerned when I saw the rods were slightly longer than the OEM. I watched multiple videos on the correct way to install them. What I learned is you replace them one rod at a time and if you put a 6 inch high stack of 2x4s underneath the basket, you don’t have to hold it up while you hook the rods through the frame. That will dramatically simplified the repair. They seem to be very high-quality. The sole exception is the replacement bushings didn’t fit like the originals. . Fortunately, I saved the OEM bushings, and they worked perfectly with these replacement rods. We’ll see if they have the same durability of the OEM parts. So far a washing machine regain the stability and no longer bangs loudly on the frame.

Excellent quality. I watched a video on how to change them, and it mentioned having to cut off the locating ears on the bottom cup that clips into the washer top. I had to do just that, and once that was done everything fell into place. The issue with the tub banging during the spin cycle is FIXED! (And we no longer have dogs barking because of the banging tub!). Highly recommend!

The replacement suspension rods work well. Installation was not difficult. The washer does not vibrate anymore.

My washer model is WTW4816FW2, and your listing states that these suspension rods are compatible with this model. In reality, they are about ½–1 inch too long. I assumed this small variation would be acceptable since my exact model number is listed, and at first everything seemed fine. However, once the washer was loaded, the extra length caused the tub and pulleys to sit low enough to contact the floor. This resulted in the pulleys grinding through my linoleum, which I initially mistook for a bad belt issue. Because the rods are advertised as fitting the WTW4816FW2 when they do not, I am requesting a refund and asking that you correct the compatibility information to prevent this from happening to other customers.

I verified this to be the correct part number I needed for my Amana washer. However, the rods were a little longer than the originals, the cups for the upper mounts did not fit my washer, I had to reuse my originals. The upper mounts themselves were a little taller but fit just barely, as in it was tricky to get the top closed back up. All that being said, in the end, I was able to get them to work and the washer no longer bangs and walks around during the spin cycle. I deducted 2 stars because they were not a direct fit, I had to reuse old parts to make them work.

Super facile à changer, plus robuste et plus longue que ceux d'origine.

It works I changed then myself very easy and it works