D-LinkPoE Injector Adapter 1 Port Gigabit Power Over Ethernet DC Powers IP Camera, Access Points, VoIP Phones (DPE-301GI)

Overall a nice POE splitter if you need to something that you can set to either 5, 9 or 12 V. I like it for testing due to the versatility. Just a few comments...- As many noted, the tab to release the RJ45 is not easy to press. If you plan on plugging/unplugging a lot it could be an issue (or add a few couplers)- It would also be nice it the unit was more compact- Ignore the 30W notes; for output power its 12v 2A (24W), 9V@2A (18W), or [email protected] (12.5W)- The barrel adapter plug is nice because you can swap out the included barrel connector wire with anything you want like micro USB.

The gigabit power/network splitter works pretty well. There is not much to say. It has a little green light when it is on. It does get slightly warm. It has 3 voltages settings. Seems like nice construction.The 12 volts coming out is 12.02 volts. For my needs i wish it was 12.3V or so but 12 volts is 12 volts I guess.

To my knowledge, this is the only TRUE gigabit PoE splitter available on Amazon with this form factor. I use it for my ODroid N2. Basic needs were gigabit Ethernet, DC barrel jack that can plug straight in to the N2 and this unit delivers.I'm giving the unit 4 starts instead of 5 for a couple reasons:- As another reviewer pointed out, the design has some flaws. Both the in and the out Ethernet interfaces have the release tabs pointing away from what you'd be looking at if this were wall-mounted. Not wall-mounting? Well it's still a little bit of poor design because just getting your finger in there to release the Ethernet cable is more difficult than it should be- No universal tip option. Not sure if this is a design you'd have to pay to use, but it would've been nice to have a universal cable and I could switch out the tips depending on the project I'd need it for.

D-Link is a smart buy

Works great with remote cameras

AWESOOOOME!!!

Worked exactly as I had hoped. Be sure to check your devices specs to ensure enough power.Placement/alignment of the ethernet connecter is poor. But once I set it up fully, I have not had to remove it so it's manageable.

Wow - this is really a bad design. Hard to imagine more mistakes from an otherwise good company. Here are the issuesa) you cannot unplug the RJ45 connector - the ejector is on the wrong side. Not once, twice - both RJ45 are impossible to remove once the device is installed on a wall. See the photob) no technical information of any kindc) it claims "Up to 30W output" - but it is actually only 24 watts output maxd) multiple mistakes on the 'specs' on the back of the device, which is good because you cannot read them after mounting to the walle) oh, when you screw it to the plywood - the slots for the screws are long and are bent by any screwf) the description has the connector sizes wrong - the connector options are 2.1x5.5mm, 1.35x3.5mmOK - now the details, if you can get past the RJ45 problem, and want to use this anyway, here is what we found out by testinga) the device is 802.3at and 802.3af compatible - so it works with all PoE switches or passive injectorsb) it accepts 42-56 volts input, mode A or mode B, either polarityc) if you use an 802.3af switch, then DO NOT load the output with more than 12 watts - it will shut down.d) if you use passive or 802.3at switches - then you can go to 12.5/18/24 watts with the 5/9/12 volt outpute) regulation is very good - better than 1%f) the efficiency is not good - 24 watts out requires 28 watts in (1 ft cables) so only 86% efficientg) the label says that the 2.1mm connector is input - no, it is the output voltage of 5, 9 or 12 volts

Ubiquiti did not have the adapter needed for their WiFi 6 Pro Access Point in stock, so I ordered this one and it works.

Bought to replace a no-name PoE splitter that died after powering my fibre modem (ONT) for about 30 seconds. That was a few months ago, since when this thing has continued soldiering on with zero issues. Yes, it's more expensive than most of the PoE splitters here but this one actually works. NOTE: The advertised 30W power output is not accurate. The device's own specs state 12.5W at 5V, 18W at 9V or 24W at 12V. I suspect 30W is the max power drawn from the PoE source.

Prodotto molto semplice da usare, un classico splitter PoE che però supporta lo standard 802.3at (PoE+), quindi con fino a 24W in output. Se avete bisogno di questa potenza lo raccomando, altrimenti personalmente prenderei lo splitter di TP-Link che supporta solo l'802.3af.Ovviamente assicuratevi di avere dall'altro capo uno switch PoE o injector che supporti tale standard.Io lo sto usando da ormai quasi un anno per alimentare un router il cui alimentatore originale forniva 12V 2A (in realtà assorbe molto, molto meno).Nessun problema da segnalare e non scalda particolarmente.Per me il prezzo è giusto e la qualità è buona.

Marque que je connaissais pour les caméras, et que je découvre pour cet injecteur PoE.J'ai choisi cet injecteur car il délivre une puissance jusqu'à 30W, contrairement aux injecteurs plus classiques et moins chers qui délivrent souvent 15 à 20W max.Parfait pour des équipements (modem ou base-station) à alimenter avec une puissance légèrement boostée.

Buon prodotto della D-Link... per il momento funziona egregiamente, ed è stato utile per una video camera di sorveglianza! Consigliato