Arnold (490-325-0012) Lawn Mower Front Wheel-15-Inch Universal Fit, 15"

Tire is as described, fit perfect on the rider, runs smooth, easy to put on and best price we found was here on Amazon

Comes with necessary hardware. My 2010 Troy-Bilt Horse came with plastic bushings, so this was an exact replacement for original equipment in every way. Those who do not have equipment with plastic bushings or complaining about the plastic bushings may want to do additional research to see if this wheel actually will work with your existing bushings / bearings. For me it was definitely worth the extra $$$$ to get the wheel, tire, and all necessary hardware rather than try to just change the tire (the old, do I really jump through all the hoops de-mounting and remounting a tire this small on this small of a rim when I can get new wheel with tire mounted plus new bushings and spacer for about the same cost? For me, it was a simple choice.) I hope this has given you enough input to make your decision. Yes I will purchase again. (Same goes for rear wheel and tire assembly.)

This tire will fit a Cub Cadet 42” deck XT1, use the brass spacer and larger insert. I was a little disappointed that the zerk fitting was plastic but it should work. Took more time straightening the cotter pin than it did to actually install the tire. Total time was about 30 minutes for both tires, just be sure to clean the shaft and apply the proper grease, have a jack, needle nose plyers, and a screw driver put something on the rear wheels to stop it from moving and you’ll be fine.

I followed the very easy instructions to install it , using the recommended spacers, and it fit very easily and without any guesswork. I just had to look up who made my Troybilt Bronco tractor first (MTD) since the instructions did not list Troybilt specifically. Once I knew it was MTD, just follow the directions in the manual for MTD tractors and the install went easily and without a hitch. I question how durable the plastic bushings will be. I imagine if they wear out that I could purchase most the bushings from Arnold, hopefully. Nice tire, nice rim, cheap price, easy install, mower is working again.

Perfect fit no issues

Very good "high flotation" wheel and tire. I honestly think this wheel and tire combo is almost overbuilt for anything a person might use it for. The tire is big and soft, yet holds air indefinitely. I need something to hoist a standby motor generator that weighs over 200 pounds, as well as other heavy items, so I am building an all electric "mobile derrick" which will have a tiltable A-frame, a tiltable boom on top of that, and a winch with 1800 pound rated cable for lifting things. This "mobile derrick" will be using the three Arnold 15-inch Lawnmower wheels that I have purchased. The tires are big enough to give my "mobile derrick" the ability to traverse soft ground.This wheel/tire combo does not come with any ball bearings, just cheap plastic bushings, one of which has a grease zerk molded into it for pumping grease inside the wheel hub. The Arnold wheel/tire combo is very heavy duty and well built, so if your wheel uses 3/4" O.D. bearings and they are still serviceable, then this wheel will probably work. In my application mentioned above, I am going to permanently mount the wheel onto 3/4" axles, and the axles will rotate on pillow bearings.

These came with a set of bushings and a spacer for each wheel so that they fit the two common different size spindles. The bushings are some sort of man-made material (nylon?) and the inboard ones have a grease fitting built into them. Another review mentioned putting the grease fitting on the outboard side--*no way*--the directions show the fitting side facing the mower not the outside. You still need to put on your outer washers, C-clip and dust cap. These came pre-inflated and look like good tires, every bit as good as the ones that came on my Murray tractor. Why mess with getting the inner tubes replaced and all when you can just pop these out of the box, swap them and be done with it. Hope this review was helpful.

The tire arrived fully inflated and looks good. The install was relatively painless. However, these wheels are not to OEM spec for my mower, a 2012 LTX 4200 Cub Cadet, even though the description stated they are. The original Cub Cadet wheels have a deeper cylinder for the grease fittings and bushings. The result with the new wheel is that it cannot hold the grease fitting in place for long, even after I've hammered it in with a rubber mallet and added the C-clip. The grease fitting will come out of the cylinder in the middle of the wheel after driving about 50 feet. The result after the grease fitting comes out is a constant, annoying swealing. It also does not stay inflated for a reason I have yet to discover. MAKE SURE THIS WHEEL IS AN EXACT MATCH TO YOUR MOWER AND OEM NUMBER.