Bedside Holster | Pistol Flashlight Holster | Gun Flashlight Holster | Under Mattress Holder | Handgun Holster | Gun Holder for Bed | Gun Mattress | Pistol Holster with Light | Bed Side Holster

6 years now and this has had no problem holding my SW M&P 2.0 9mm Compact (size of Glock 19). I wish the barrel ledge was about 1/2 inch deeper but its done just fine. not great if you have a weapon light on but I prefer to use a seperate flashlight at home anyway. This way I'm not pointing my light and weapon at the same time only to find a pet or loved one most noises in the dark are not threats...

Works great! I don't have a box spring, just a metal bed frame, and there's no issues! I just use it to hold my Bryna and I have easy access to it!

I chose this hard plastic style mattress holster because the cloth ones seemed to flop around too much. I would like to have a bit more variety in how to place each component; it is possible to move the flashlight holder so it will be vertical but there is no place to move the magazine holster. The magazine holster hangs over the edge of the plastic and has sharp edges, requiring some file work to soften the corners. It is possible to invert the entire unit so it's higher up on very deep mattresses, which is impossible with the cloth units, but I found that it works hanging down in my situation. I do not use the cell phone holder as my phone is on its charger at night. The plastic bar that adjusts up or down as needed for the longer barreled guns will allow the trigger to be covered while the gun is in this holster, a good safety feature. I also like that the elastic webbing is attached with hook and loop fasteners, allow adjustment of the tension based on the size of the gun. I had considered making something similar using angle aluminum but this does just about all I wanted for a reasonable price. Overall a good product even if not quite a 5.

This is my third bed mounted gun holster and I can honestly say that it puts all my past experiences to shame! The other bedside holsters I’ve owned and used needed to be readjusted on a daily basis, sometimes more than once, but this holster has not needed to be adjusted once, not one single time, in the months I’ve been using it. Now the strap that is actually supposed to hold the gun could certainly be a little tighter, and the floor plate that is supposed to stop the front end of the gun from sagging could be a bit lower for full sized pistols, but I have the perfect fix for that! Order a soft IWB Holster by Houston Holsters on Amazon (make sure it is for right side draw in order for the belt clip to attach to the strap on the bed holster meant to hold your gun) and stuck it inside the gun strap on the bed holster, then BAM! It’s nearly perfect! The strap meant to hold the magazine could also be a bit farther from its respective floor plate to accommodate extended magazines, but it still works fine with my Magpul 21 round 9mm magazine for the Glock 17. Last piece of advice, it is harder than you would think to find a flashlight to perfectly fit the 1.25” tube/holster on the bottom of the bed mounted holster, so I found it MUCH easier to go to Lowe’s/WalMart/Harbor Freight and measure the flashlights I found acceptable to find one that will fit just right. It’s much more efficient than ordering multiple flashlights from Amazon trying to find a good fit (I went that route initially and it was super frustrating!). Overall, with a few simple modifications and tips, this is hands down the BEST bedside/bed mounted gun holster that you will find of it’s kind! Even though it could be improved upon, it is soo far ahead of the comparable products that I’ve tried, I STILL give it a full 5 star rating!! You will not be disappointed, ESPECIALLY for this price!

Overall, well made. The elastic holds smaller frame guns reasonably well. However, full frame /size ones tend to slip off the muzzle platform and / or turn on an angle where it slips off the shelf and is held sideways by the elastic. Makes it a bit difficult to draw if laying in bed. Also makes a sliding / grinding sound when drawn; not good if trying to be silent.Also, this doesn't work if you have a light mounted.To recap, for a compact / sub-compact, this could be a good choice. Otherwise, you may want to look at other options.