TEMCo HP0000 - Air Hydraulic Pump Power Pack Unit 10,000 psi 103 Cubic in Capacity - 5 Year Warranty

The hose that comes with this unit is 4 feet long. This is too short for most applications. There is usually a hydraulic store in most large towns and a 10-foot hydraulic hose that withstands 10,000 psi will make things more practical. Take your 4-foot hose with you and have them match the fittings. My 10-foot hose cost me $82.Final test makes this a 5-star pump, for this price. Using the Temco HC0014 cylinder it raised the center of my house using half its power. The house is 3-bedroom, 2 bath, 2 car garage and the footer beams are 20 inches deep. The pump is slow under high pressure and takes 50 seconds to move the cylinder 6 inches. Compared to all things that must happen on a job this is not a lot of time. To go 10 feet, it would take 17 minutes of pumping time. For a full-time professional with only one pump this might not be fast enough.After non-stop use on 2 peers that went down 12 feet, the motor was too warm to hold the back of your hand against but not too hot for an electric motor. For a full day of heavy use, you might want a fan blowing on the motor. The hydraulic hose only had a little warmth to it so the pump and cylinder were doing fine. There is no gradual release mechanism. When you press on the back side of the control peddle, the house drops immediately. The return on the cylinder is fast enough.My foundation professional used it from 1 floor cutout and 3 tunnels to reach 3-footer areas. The pedal control made the operation very easy for the operator to control. Once again, it required a longer hose. I would recommend at least 8 feet. Our 10 foot hose was perfect and could have been 9 feet long.

Simple, high quality, quiet, no issues with bleeding it worked great right out of the box. Used on my motorcycle lift with 900 lbs. bike. Lifts it like there is nothing on the lift. Fantastic little pump!

After leaving the bad review I had an email and new part being shipped to me within a couple days. Possibly it was an oversight. Product is great and warranty is great once they respond.Product worked as it should for about one year. Reached out to warranty team, received an email asking for proof of purchase and description of problem. Responded with the requests, then nothing. No emails, no calls, no return instructions, etc. Thank you TemCO for making a disposable product.

Pump arrived quickly in a well built protective package with out damage. I used it right away with my new TEMCO 30 TON HOLLOW CENTER RAM to remove a 3" x12" stubborn hydraulic cylinder pin. Worked great with no effort. LOVE IT !

I used the Temco hydraulic pump and Cylinder (see photo) to construct an electric hydraulic press for 20 Ton force and 10,000PSI pressure in closed system.Both components arrived after two days in great shipping container with no defects. All quick-connect and hose were part of the package which simplifies installation.A detailed installation guide is more like a warning document and an operating manual does not exist. Two request emails to Temco were not answered yet.Please note it is made in China but the quality and price are great. It comes with five year warranty and 1 year no questions asked return policy which I tested on a previous product.

Nice little HPU. We used it to replace an air over oil HPU. VERY quiet.Removed one star for QC. The handle was either bent or welded incorrectly and made removal of the filler cap impossible. I had to grind a notch in the handle in order to unscrew the filler cap. I did not ask for a new one as we needed it that day so we fixed it.

I originally purchased the Vevor 2510 due to less expensive. After. Month it died. China crap. So I bought this one. What a difference. I use to to push my 20T press for forging Damascus steel. The flow rate it definitely faster. Good quality product and excellent performance. High and low flow non pressure vs high pressure. Still pushes 5-12 tons faster than the. China models. Great buy.

This is a great little pump with a 5 year warranty and fits perfectly on a Greenlee Table Bender. It is quiet, works well, and the price seals the deal. Very pleased.