Lomanco Power Vent Attic Fan Motor 1/10hp 1050 RPM 115 Volts F0510B2944

This motor replaced my old one perfectly. Looking at the picture I wasn't those little tabs would work. They do fit perfectly and replace the original triangular plate that mounted my old motor. The BX cable shield from the old motor also fit over the wires and threaded right onto the new motor.

The Lomanco Power Vent Motor Replacement F0510B2944 is a top-quality product! Easy to install, durable, and performs flawlessly. Highly recommend for efficient ventilation. Excellent value for money. A must-have for smooth operation. 5 stars! ⭐⭐⭐⭐⭐

replaced my old motor with this one and its working great. Motor is quiet and easy to install. ***UPDATE*** 5/21/2016 Install it on June 4, 2015. It was working great during the summer. My attic gets very hot and the motor seems to be on constantly. Then this year, May 18, 2016, I went up to my attic and it was hot, over 95 degree. I set my thermostat to 90 and it wasn't working. Checked the current and it was getting electricity. Motor died. Call CSH Inc. who was the seller through Amazon. They were very nice and explained that I had to go through Amazon for the 1year warranty even though they were the seller since I bought it through Amazon Prime. CSH said to call them back if Amazon didn't help and they would help me. Amazon said they don't do warranty but would take it back with a 15% restocking fee. Amazon said I could call the manufacturer for the warranty. So I called Lomanco and they honored the warranty with no problem. They asked for the model #, manufacturing date which is in the motor but I didn't know it - I give them the date on the box and when I bought. They sent me a new replacement one. I didn't have to send back the defective one. I received it in 5 days, call Monday received it Saturday. Excellent customer service, excellent warranty. I hope the new motor lasts a lot longer than a year.

Works perfectly as a replacement so far. Found a YouTube video which was helpful as a guide - search for: Lomanco Attic Power Vent Fan Motor Replacement Maneuvering the fan/motor assembly out of the enclosure is much easier than the video shows - you might have to bend one of the three support arms (after removing the screws) to pull it out, but that's all that is necessary. It's much easier to disassemble and reassemble the fan blade to the new motor when it is completely out. The top of the shaft of my old fan motor was rusted so you may need to sand it a little and add some type of lubricant on the shaft (vaseline or WD-40) in order to be able to bang/shimmy the fan off the old one- once you have the old fan blade off, then it slides very easily onto the new replacement - put it at about the same offset from the top of the shaft as it was on the old fan. When reinstalling, after all looks connected, before powering up, rotate the fan freely by hand to make sure there is nothing hitting. If anything of the enclosure is hitting (such as a screen which is part of the outer enclosure), and the fan looks like its spinning pretty balanced, you may be able to bend the screen a little to stop the hitting. Once all looks good, then power it up and all should be well. My old motor was the exact same model with a manufacturer date in 2005 - I hope I can also get 10+ years out of this next one.

The old attic fan motor died and I initially bought a new motor from a large box store with the thought to reuse the blades I already had. BUT, the set screw was so tight into the motor rod that it was impossible to release it. My advice, don't bother. Buy the motor and new blades together. There is no instruction sheet enclosed so KEEP YOUR OLD ONE onhand so that you know which way the blades are facing). My old attic fan was attached using a belt bracket that went around the motor so the installation of this one was easy. You will need two people to install it, one to hold up the fan while the other one tights the screws. It's simple to rewire it, turned on the power and the fan went round and round. Hopefully it'll last at least 5 yrs. (the number of years my 1st one lasted. The blades seem sturdy enough even at $16. Replacement Fan Blade for Lomanco Power Vent Motor # 14393 For those who don't want to go onto a 2 story roof to replace an attic fan, this is the way to go. MOTOR AND BLADE COMBO

The Lomanco motor was practically speaking an exact fit. Some installation notes. Mine had a belly band connection. So the extra hardware was not necessary. I re-used the armor cable from the old fan. I loosened the three 3/8 in screws and bent back the arms just enough to angle out the old motor with fan blade attached. I took the whole assembly to my workbench sprayed down the set screw with PB blaster. I let it set for a little while tapped it with a hammer and used a long 5/32 Allen key to take it off. The shaft was shorter but I put the fan blade all the way at the end of the new shaft as far as it could go and there were no issues with clearance. I also added some extra 3-in-1 oil into the oil holes on both sides of the motor for extra longevity hopefully. I took my time and it was about an hour 's job. Watching the videos and having the right size Allen key and sockets in advance helped.