WagnerControlPro 250R - Airless Paint Sprayer for Wall & Ceiling/Wood & Metal paint - interior and exterior usage, covers 15 m² in 2 min, 110 bar, adjustable spray pressure, 9 m hose

The instructions are seriously lacking, but once mastered, this machine works well. Took me around 3 hours to figure out the quirks, so to save you some time:1. contract matt emulsion with the correct filter and nozzle (according to instructions) will need to be watered down by 10-20%2. the pick up / collector needs to be submerged well below the surface of the paint, otherwise the machine loses pressure, the pump stays on and the gun just dribbles. Its clear to identify, and happened repeatedly when the 10 litre paint tub got down to around half full (despite the pick-up being well submerged.3. cleaning is best done by pulling through clean water for a few minutes (with spray nozzle removed), then give the gun, filter and pick-up a thorough clean. You can avoid wasting paint by catching the watery paint in a container and use the next day to dilute your neat paint.its not quite as messy as I expected, doing ceilings goes everywhere as you might expect, but with walls its not bad, and the spray focus is pretty good. Its a nice bit of kit that will save time if you have a lot of surface to paint. Probably not ideal for the home, but warehouses, commercial premises etc., its ideal. And at this price, cheaper than hiring something similar.

Great product and value

Painted our large kitchen in a day. The finish is excellent. The spraying was done in the time it would have taken me to paint one wall with a brush - not the ceiling. That essentially is the good thing.The bad is the time it took to mask up, the disruption, the overspray, the fabric that allowed overspray to seep through. In short, making and cleaning was a nightmare. I came away thinking what a great tool it is in the right circumstances. If you have an empty house to paint, this is the machine for you! If you have several large surfaces to paint, it will do it in no time. Getting the paint mix right was relatively easy. The gun was fine, easy to use... but hard to clean. This is another minus - cleaning the machine and pipework. I wanted it to be spotless so it took a long time. Again, this is all about the amount of painting you have to do - the more the merrier. The less the more miserable. It is that simple.

When looking at painting the whole of our barn conversion, I looked at saving money on paying for a professional decorator to paint all internal walls. As I had so many square metres of plastered/skimmed wall to paint I decided to buy this spray gun after looking in to on-line written and video reviews. The results I've got with this spray gun are little short of spectacular. Whilst the painting is really fast, preparation of the wall and masking up windows and steel girders to protect them from the spray does take HOURS. This is not a criticism as preparation for most things is where jobs can be awful or amazing. I went over all walls with my hand to 'feel' for nibs of plaster and removed these with sandpaper and then took time to mask off window frames. I also found a few great tips and hints to get the most out of the gun, such as ensuring the cable was clear of all items to avoid snagging during spraying... and making sure spray starts and ends away from the wall (to avoid drip regions). I've had quite a few trades in and all have been really impressed with the paint job. I cant recommend this product highly enough. It does need cleaning through thoroughly after each panting session but after a few sessions you get pretty slick at emptying the paint back into the tin and as the diluted paint starts coming through, divert this to a separate tin and use later to dilute new paint. I also found that i needed to really look after the nozzle parts. If I took a break I remove the nozzle and wash it through leaving it in warm water for the next session as this can get bunged up leading to 'spits' of paint if left. The great advantage of this system is (i) quality of finish - I could never get a finish like this with a roller or brush (ii) speed - it seems to apply a few coats at once so although it gets through the 10L pots quickly, its putting a thick coat (maybe equivalent to 2-3 coats with a brush?) in one go (iii) consistency - if you are methodical in applying the paint (you have to keep a constant speed or you'll get light patches or pooling of paint) the look is amazing. I've had NO experience painting with a spray gun before buying this and following the instructions you'll get a fantastic paint finish. I found that the finish i got was as good with 'good' paint (paint shops recommended own brand) as it was with expensive brands (such as Dulux). I don't think anyone can tell which rooms are finished with which paint. I'm sure this is due to the spray gun. I didn't find cheaper paint causing any problems with the spray gun indeed, a 5-10% water dilution (with VERY THOROUGH mixing using a drill mixer) was ideal with all paints used. I've not tried the 'Diamond' Dulux paint through the spray gun (for scrubbable areas of wall such as hallways) but I expect it is just as good. I've had 2 offers to buy the machine after I've finished with it... the results have been that good. HIGHLY RECOMMENDED.

If you're a beginner like me, don't bother buying this product. You have to be expert and you have to know what you're doing. I had to spray a wall or spray anywhere. Just don't waste your money

Sometimes it is better to buy the original / best brand so I decided to replace another problem sprayer with this one.It works well, is well made and nice to use.It suffers from the same problem of wasted paint and horrible cleanup that all sprayers suffer from. It uses about 1.0 - 1.2l of paint by the time it is primed and reaches the spray nozzle. I haven’t managed to achieve spraying with no oversray / spray dust as claimed in the blurb but maybe more fiddling with pressure / practice may help.Finish achieved is perfect; I am not new to spraying but not a pro.

I purchased the 350 M sprayer and it’s brilliant. I am painting out a large workshop area and I started with the roller and brush method - it took me about 4 days to do half of it when someone told me about the airless sprayers - I had never heard of them. I wish I had sooner - what took me 2 days with the roller and brush I did in 2 hours, it’s amazing and really easy to use and it leaves a really nice finish. So the down side is that you must mask any areas you don’t want spraying and cover the floor really well it’s not so much spills but the fine mist will cover anything you don’t cover. Cleaning the machine isn’t difficult but takes a little longer perhaps than cleaning a roller and tray but who cares when it saves so much time. The machine isn’t bulky or heavy and is easy to move around all you need to do is plug it into a power supply. Would I recommend this product - absolutely - it’s already paid for itself in the time it’s saved me.