VEVOR Dirt Bike Lift Stand, Motorcycle Jack Lift Stand 440 lbs Capacity and Hydraulic Lift Operation, Adjustable Height Hoist Table, for Dirt Pit Bike Repair, Maintenance, Dirt Bike Accessories

Update 5-21-24: I bought a second dirt bike (2023 Husqvarna FC250). A full motocross bike. The stand also works great with that. I just set the platform higher so it will just get both wheels off the ground. And then set the locking nut underneath it snugly. Works great for this bike too, so I bought a second one. And here is a tip for people: Rather than banging on the arm on the locking nut with a hammer or mallet and risk breaking off the arm.. (You want this positioned snug against the base of where the spindle comes out- to provide more stability). Instead position it so it is snug, and then rotate the platform to get it tight. I have a 21 Honda CRF250F and this stand is perfect for what I need, and at a good price. I also have a regular stand that is 17" high, and trust me, its not that fun flipping a 265 pound bike up on a 17" stand. I can usually do it, but sometime I have to do it a couple times, and then reposition it a bit after. With this stand, I can just position it under my bike and push down on the lever. So much easier! A couple tips for people: Keep the height as low as it can go and still get the bike as high as you need. For my bike, I can leave it on the lowest setting and it can still get the bike high enough for me. If I want the back wheel off the ground (to say lube the chain), I position it more towards the rear, and let the front wheel rest on the ground. No need for me to get both wheels completely off the ground at the same time. That way it stays very stable. I also raised the platform until it just barely fit under my bike, and then it raises both tires a couple inches off the ground. It will sway a little like this if you push on the bike, but it still feels fine to me. If you have a full MX bike with more ground clearance and suspension travel, you will probably need to raise the platform a few inches.. I expect it might feel a little less stable. So I would set the platform only as high as you need it to be to get the job done. Also there is a locking nut on it, so I rotated that in place and then rotated the platform until it was snug. Works for me. I also like the hydraulic thing on it, to make it drop slowly rather than just plopping the bike straight to the ground when you release it... And I don't know if this is how they all ship, but mine had an extra corner pad (for the "feet") and an extra c clip for the pins. I really like the convenience of this stand! Hope this helps someone.

Pretty light weight and shipped almost completely assembled, just two pins and two clips and its built. Lifts a klx300 with ease, it's stability is good enough, just pick a level surface and in moments the bike is off the ground. The height is adjustable by means of the threaded upper platform. Works great.

Seems to work good, but it is way too tall for the bike I bought it for. Check to make sure it's not too tall for yours before you buy

The Vevor lift stand is awesome. The plate can be raised or lowered to make the stand taller or shorter as needed. When the handle is pushed down to raise the stand under the bike, it will hold itself in place really well. I do like that it also has a simple lock to hold the handle from dropping. The hydraulic is strong: it lowers slowly when the handle is released. The weight makes it feel sturdy, this isn’t a lightweight stand. I’m strong, but I don’t like trying to lift my dirtbike onto the normal stand. This is a life saver!

Works as it should its just the lifting platform is wobbly the bike doesn’t sit straight

For not a whole lot of money and without getting a hydraulic motorcycle lift, this works really well. Lifts my XR650 so both wheels are about an inch off the ground. To make it really stable, figure out the height you need it, then pound the lock ring into place with a 2lb hammer. Otherwise, the top plate will rock and turn as you're working on the bike. Very compact to have around the garage and easy to slide under the bike.

Very nice and easy to adjust, lift and lower. Solid. Half the price of other comparable lifts. Using it on a KTM 250 XC and Kawasaki 112.

Work as advertised.