G10 Fiberglass Garolite 3D Printer Build Surface Plate Semi-Flexible Sheet 235mm/9.25"(Black Color),200/220/250/257/310/400mm Available

This is an outrageously high-performance print surface overall, and will last a very long time if you treat it properly. The main selling point for this surface is that it performs well on PLA, ABS, and PETG (and possibly more) without ANY bed preparation, glue stick, etc. PLA sticks like glue at 55C. For a surface this smooth, it has unusually good adhesion. PETG sticks nearly as well at 75C, and adhesion can be improved by slowing the initial layer. ABS is a bit more demanding, but with a slow initial layer, and a high bed temp (100C works well for me), you can print reliably. ABS still occasionally shows signs of lifting in the corners of prints, but it has never caused a print failure. All of these materials will self-release once they have cooled. You MUST WAIT for this to happen, or you will damage the print surface by yanking on your parts. This is a fairly soft surface, and can be scratched and damaged easily. Do not use a scraper on this bed. Do not allow your printers nozzle to drag along this bed. They will permanently damage it. I recommend cleaning it with isopropyl alcohol and a clean rag. This specific sheet (235x235) is perfectly sized for an Ender 3 or K1. The edges are a bit rough, the corners are a bit sharp, but the sizing is perfect. I have bought a few of these, and I find that usually only one of the two sides is perfectly smooth. One side usually has some scuffs in it.

If you're looking to upgrade the surface quality of your 3D prints then going with a G10 build plate is an absolute must! Nothing beats a nice smooth texture. Sometimes a textured plate is necessary for some filaments but I try to print on the smooth surface every chance I get because of the glass-smooth bottom results you get. Some parts just need a smooth surface. I think this plate is built very well and it functioned exactly as advertised. It's true G10. I'd buy it again. I have not and issues with PETG, PLA, TPU sticking everything I have printed continues to stick very well to the bed. I haven't tried ABS or ASA but I rarely print with those filaments.

Says 3D build plate. Yet, it flops around. Not meant to stay out. False advertisement to say the least.

Please note, that I received exactly what I purchased as described, well packaged and shipped to me without complaint. I only give this four stars because I bought this in hope it would be better than the pei plate that I am currently using, It works ok for PLA, things stick but it's not better than what I already have.

Works best if the garolite is heated to 70c for a few hours. Good adhesion when printing, then lets go when cool. 1.5mm is rigid enough to level the small bed deviations. Some history marking after use. Cheap enough if you shop around. Never going to use anything but this on my printer.

I recently switched to a G10 build plate on my Ender 3 Pro, and it’s been a fantastic upgrade. It installs just like any other build surface — I clipped it onto my heated bed with binder clips, and it was ready to go. No adhesive or fancy prep needed. The bed adhesion is amazing, especially for materials like PLA and PETG. Prints stick down firmly without needing glue stick or hairspray, but they also pop off easily once the bed cools down. It’s super durable too — no scratches, dents, or peeling like you get with some other surfaces over time. Print quality stayed consistent, and I didn’t have to mess with my Z-offset much either. Just leveled the bed normally, and it was good to go. If you're tired of constantly fighting with first layers or worn-out surfaces, G10 is a simple, reliable upgrade. Highly recommend it!

Was very nicely packaged in a bubble wrap sleeve and another plastic sleeve inside the bubble wrap but unfortunately when I unwrapped it the product inside was somewhat scuffed up there's no way this happened in transit because it was well packaged product overall is very nice looking I just wish it wasn't scuffed but the functionality should not be affected

Time will tell how this build sheet holds up, but for now prints are great! The printer I bought this for only uses pla and at 60C it stick incredibly well. Let it cool down to 30C or less and it comes off the bed with no effort. No scratches in mine like others have said and it is very straight and flat. Highly recommend especially if you're still using an anet a8 in 2025.