Harbot 1950 2050 2150 Carburetor For Poulan Chainsaw Parts 1900 2055 2175 2350 2450 2550 262 Wild Thing Chainsaw Replaces 545081885 530069703 C1Q-W8 C1Q-W14 WT-891

My Ramblings Been a while since I tuned up this chainsaw and it has begun to start hard and run rough.. So, let's just replace it all, because it's cheap to do so. To the Point or TL;DR Two surprises: Primer Bulb Intake is on left side; however, Not in the way of throttle linkage. Throttle on both left and right side of carb, also, doesn't interfere with anything. It wasn't missing any pieces or parts. Chainsaw started after some priming and a four good pulls. Have your screwdriver ready to adjust. Adjusted it and runs smoothly. The carb didn't change my chainsaw it into a new one, but it made it run smoothly for the first time in a while... So worth $18. The Bad Stuff None so far Who May Use/Like It Those needing a tune up on their very old, but still useful Poulan 2150. Me Final Thoughts Go ahead and buy yourself a new chain while you're at it. My old saw running smoothly again. I could use a little of that myself. That's my story and I'm sticking to it. Hope it helps! All the best, Just Benjamin Reviewed: Brand: Harbot Cost: $17.88 at time of review. 1950 2050 2150 Carburetor For Poulan Chainsaw Parts 1900 2055 2175 2350 2450 2550 262 Wild Thing Chainsaw Replaces 545081885 530069703 C1Q-W8 C1Q-W14 WT 89 891 WT-324

Worked perfectly with no adjustments needed!

I got this carburetor to replace the original on my Poulan 2375 chainsaw. It was listed to fit my model, but I found that it differs from mine, and in my case required a different part to fit. The kit has everything needed for a fuel system maintenance. It comes with a fuel filter, two sizes of fuel hose (small fuel feed, large fuel return), a new priming bulb, an air filter, a spark plug, and the carburetor with the gasket. Such a great price for everything included. I had some trouble feeding the fuel lines into the holes, but got it eventually. The addition of a fuel filter is nice as my saw never had one originally. The carburetor fit just like the original; however, when I went to assemble the air filter, the housing didn't fit this new one. My saw must be an earlier version of the model number, because this replacement has a different Choke Control Rod. While the new carburetor has a better choke setup, the air filter housing isn't the same. I had to get a replacement air filter housing that has a bigger relief cut out to allow for the larger new one. So check out your old carburetor when purchasing this upgraded one. Assembly was pretty easy after getting the hoses installed, and the saw started right up when I was done. I only had to make a small adjustment to the Lower Speed/Idle setting and I was good to go. I really like this upgraded carburetor kit and only wish I'd done it sooner.

I needed this for a Poulan Wild Thing 2375 that had the early Walbro WT-324 shown in the second picture, with both fuel lines on the same side. This carb, as shown in the listing, has one fuel line on each side, and the choke linkage is a little different. I had my doubts it would work, but the throttle linkage is the same, so that hooked right up, and I had no problem with the choke side either. It comes with new fuel lines, so you have plenty to route it the new way, and everything fits without having to alter, bend, customize, or otherwise mess with. Simple and effective replacement. Just make sure you know the fuel line routing, because when they crumble taking off the old carb, and you don’t know where they go, it’s not fun when you hook them up wrong. Simple to adjust, saw runs great!

Definitely made the chainsaw run like new.

Preface: I repair a hundred or more of pieces of equipment per year, so I’m familiar with these. And my saw was running fine with the OEM Walbro carb but leaked a couple drops of fuel from a stripped screw hole. For safety in the woods figured I’d just replace it. Does not fit the 2150 it’s supposed to without modifications and/or a replacement air filter housing (I modified the original drilling out the choke bump and plastic welding over mesh to seal it up) And had much trouble getting it running enough to even start tuning after replacing everything-fuel lines, filters, gaskets, carb and spark plug. All 3 adjustment screws were fully screwed in not set to factory settings. Not plug and play this time… took about 3-4 hours total and still not running properly.. Advice: buy this carb to use the gaskets/diaphragms and new needles to rebuild your OEM after thoroughly cleaning it and avoid the headache of modifying. Factory L/H settings will be 1.5 turn out from gently seated on each go from there

Nice little kit. I'm running this on my riding mower now, put on about a year ago. No problems with it.

In the listing it says it fits the Poulan Wood Shark 1975 but it is not even close. I would return it but it’s already been in the shop trying to make it work. The choke set up is wrong. It rubs against the plastic housing that holds the air filter. When installed you can pull the choke but it will not release do to hitting the cover. If you didn’t mind you could notch the plastic cover out and make the choke function properly. The other issue was the throttle linkage hits the nipple for the fuel line. You can tweak it to make work as we did but no adjustments on the High and Low settings could get the saw to run properly. On the other side of things the price was ok since it came with a new plug and fuel lines and fuel filter I can use on other projects. If your looking for a kit you can just toss on an go look at your style carb really good before getting this kit. @generationx1971 on YouTube