Invisible Ring Spacer & Guard – Ring Size Adjuster for Loose Ring, Connector & Resizer, Any Size Fit

I was a little skeptical but decided to give it a try and I’m so glad I did! I followed the instructions an refrigerated bottle for a few minutes, but the gel was too cold to come out of the bottle, so then I ran the bottle under hot water and tested the control & thickness on a paper towel. I felt pretty confident, put in my glasses, took a deep breath, and maybe 15 minutes later my two favorite rings fit! The only reason it took that long was because I cured each layer of gel 3 times because I knew I would be using 2-3 layers of gel to get it sized and wanted to be sure it was dried all the way through.I’m pretty rough on jewelry and it’s been about 6 weeks now and they’re still perfect. I wear both rings daily, wash my hands 1000x a day, forget to take them off when doing yard work, etc and there are no issues.Today I took out the little kit to use on another ring and followed the same beginning steps, but was unable to get any gel out of the bottle. Much like super glue, the nozzle tip was dry. Easy enough to fix, I put on rubber gloves, pushed a needle down the center of the tip, pulled it out then popped the top off, and did the same from the underside of the top. Still no gel, but plenty in the bottle so I sat the bottle in a mug of hot water for a few minutes and it was flowing again!I have attached up close pics of the “sized” side of the ring on top of my finger, and the sized part underneath where it belongs. Unless someone is REALLY examining your finger, they’ll never be able to tell. I will absolutely purchase again and have recommended this product to several of my friends.

I have tried so many ring resizing methods, and this is the best! I've tried everything from the little coil things to spending $150+ having white gold tension adjustments put into rings, so I have fairly extensive user-level experience. I can, without a doubt, say this is the most effective without the drawbacks.I put it on this ring over 2 months ago and it's still perfectly fine. I do dishes daily, so it's certainly gotten a solid test.For the 2nd picture, I removed the bumps just now to show the band underneath. I would imagine it would be problematic if you applied it to a setting, but it's only supposed to be on the band, which makes sense. It has not affected the ring finish itself at all. I only have 14k white gold, so any change to the finish would be pretty obvious.Good to know info:#1 - I have skin reactions to lots of things, but this does nothing.#2 - I screwed it up (twice) and it was so simple to remove and reapply. Soak it in super hot water in a bowl for a few minutes and pry off with a strong plastic or wood utensil. I have an acrylic pie knife that works great.#3 - I did the "speed bump" formation and my ring barely spins. Tip: put the dots in what would be the bottom corners of a square for good placement.#4 - it's totally adjustable, so if my weight fluctuates, I can resize as needed.#5 - it works on thin bands as well as thick. The jeweler had to put the tension thing on behind the setting with a thin band, but this doesn't have those limitations.Definitely do thin layers (or dots) and then cure once or twice, then go back and add more. Also do one spot, cure, then do the next spot. There's no need to do multiple spots at once, and it's less work to apply, test, apply than apply, test, remove, apply, test, apply.

This worked well for me, however, it’s day one so I’ll update in a week or two to confirm the staying power of this.I had a thin pinky ring that was just a half a size too big but it would constantly fall off.Used the solution and the provided UV light to add a thin band into the ring. The provided ring stand seems to not stay upright so I just held the ring in my hands while I cured it with the light. I did have to hold the ring upside down and kind of turn it a tiny bit as it started curing- the solution isn’t super runny but if you hold the ring upright and the band is very thin, it might ooze to the outside of the ring.I had to apply the gel and cure about 3x to get the thickness I wanted to make the band fit perfectly. There’s a slight smell but it doesn’t seem to stick around.For now, served its purpose well but I will update with additional notes in the future.Photos attached- I’m sure I could’ve done a better job but it’s a cheap ring and not that serious to me :DUpdate: a week later and it’s still holding up perfectly so I’m pretty happy with this.

So far it seems to work well. I did have to apply 5 different layers and us the light twice as long, but so far so good.

Tried a metal ring size that you wrap around the ring band that would basically bridge a metal strip across the ring but it makes my ring look cheap and uncomfortable. I thought I give this product a try, it includes a bottle of thick liquid sizer that you add to inside of the ring and then let it cure it with the included UV light.I do like that the UV light has a built in timer that is set to 60 seconds and then automatically shuts off. I bought this ring shown in the picture, it was what I was looking for but it only came in a size 12 and I wear a size 11 ring. I added layers of this liquid sizer until I was able to get to a wearable size 11 ring. After letting the liquid sizer cure I then carefully trimmed the edges of the sizer flush with the ring band with a sharp knife. Now I have a ring that looks great and wears great!

This is the best ring size adjuster. I’m so glad that I purchased it. I have tried them all….the plastic ones that fit on the back of your ring that end up getting a dirty color that happens with plastics….and those little sticky tabs that ALWAYS fall off ….and the little round squiggly things that you wrap around your rings. None of them worked well for my soldered wedding band set. I am still losing weight so I wanted to wait till I got to my goal weight before I actually took my ring to the jeweler and this glue is absolutely perfect! It works fantastic and you cannot see it at all. Best invention ever. This kit is a great value for your money super simple and it comes with the little UV light. 👍👍👍