airgoo Addressable RGB PC LED Strip, 13.78 x 0.39 x 0.12 inches Clear Silicone Covering, for 5V 3-pin argb Header or AG-DRGB16 SignalRGB Controller(Not Included), Built-in Magnets, Easy to Install

This is a good discrete kit for adding addressable LEDs. The magnets make it easy to mock up and ultimately install the strips using the self adhesive.Be aware, for a Cooler Master RGB/Fan Hub the connector on the provided aRGB interface cable was a little too wide to fit into the hole in the Hub case. This would probably not have been a problem for my motherboard directly and it was easily remedied by trimming away some of the rubber on both sides of the cable's connector using a hobby knife. For those not wanting to modify the provided cable you may want to consider using a stock Cooler Master cable and moving pins between or splicing into the "three" pin locking connector used on the strips. It looks to be of the standard RGB LED, again "three" pin. I docked one star in my review on easy of install due to this, but otherwise I am very happy with the provided parts.They are bright enough for projected light to be seen behind a smoked acrylic cover of a Cooler Master case. I have them tucked under the upper and lower lip of the case. So far the are still in place and the adhesive appeared to grab well during install.For install and size comparison, in a CM TUF Q300L the LEDs reach the entire length of the upper and lower lengths of the case. The provided interface cable and extension worked to get the strips installed and wires routed out of sight. They are working with ASUS Aura on a CM RGB/FAN Hub perfectly.

I just wanted some lighting inside my chassis - didn't necessarily want or need flashy patterns or rainbow effects (although this has that too). I found it convenient to be able to just power this by SATA and use a remote control to change the color, as oppose to using the rgb header on my mobo. I usually just alternate between static colors to maintain a sleek/clean feel.For the value this as exactly what I needed. The strips are about the size of a typical side to a case and the magnetic adhesion actually works quite well and there's no slippage. Easy to install and works as intended, though some of the rubber was dried out, the strip cracked but that didn't impact the actual light strip, so a little tape fixed that right up.No malfunctioning LEDs or anything - worked great for my DYI build - good value for what I wanted out of it. I prefer the convenience of just using the remote control.My only criticism is that some of the colored buttons on the remote display inconsistent colors. For example I couldn't get purple from the purple button - it simply shines blue. But otherwise everything works fine.

The media could not be loaded. Package arrived on Wednesday with everything listed. One strip did not work. I contacted customer service and they responded within a few hours. The following Friday (two days later) I received not a single replacement strip but a complete package. That’s great customer service!On to the product- installation is self explanatory knowing that you must install this to an addressable rgb 3-pin 5v header. Magnets are sufficient at securing the strip to a single straight run but trying to turn corners it may struggle, that’s when the adhesive helps out and holds the 90-degree turns tight.When connecting the strips in series or daisy chain, the light timings on each strip does not sync perfectly. There is a slight delay in the latter strip, maybe 1-2 second delay. In order for the timings to sync in both strips, you need them to run in parallel or use a splitter. The package does not come with a splitter, it comes with and extension. I used one of the included extra cables to make a homemade splitter and connect the led strips like that. Now both led strips sync up perfectly.Overall, I’m happy with the project and very satisfied with the customer service. The lights look great in my NZXT H1 case.

easy installation with good color accuracy and adhesive magnet quality. looks nice and isn't too sharp on the eyes. Length for me was perfect for installing on the top and sides of my pc but it has one caveat in the length department. For whatever reason, the motherboard 3 pin cable was installed onto the extension cable meaning if you use something like a fan hub that sits in the back panel / bottom of your pc area you will have to plan accordingly, if you plug it into your motherboard only though, you'll be just fine. solid quality on the magnets and lights no complaints but the end that isn't plugged into an extension does stick up so tape it down if you'd like.