BANVIE Car Keyless Entry System, Car Central Power Door Lock with 4 Button Remote Control Transmitter, Electrical Anti-Theft installations for Vehicles

These work perfect. The installation was not bad at all if you are pretty good with DIY and have any experience working in a car. It took me 30 minutes. The diagram shows wiring to the battery but I couldn't find a good spot to get through the firewall so I ended up going with a fuse tap going from the fuse for my radio which is a constant 12V. Very easy and the rest of the wiring was exactly like the diagram. I did this on a 2002 Toyota RAV4 and both yellow wires and the black wire were grounded. Then red wire to the fuse tap for 12V. And then find the specific wires for your unlock/lock and tap into those with the white wires. The remotes are really nice too and look fancy. I did not hook up tje brown wires to the turn signal lights or the trunk pop wire as I have a hatchback. 10/10 would recommend

Very well built the remotes are solid. It has a pretty good range that it works. Plenty of options how to hook it up for your system.I am happy with it.

It seems to be an affordable remote keyless entry. Easy to install.

Worked great for 30 days.Now it is just a pretty light.

I'm not thrilled with the range of this product. I have to be within 25 feet or so to get it to operate at all. I even went to the trouble to extend the antenna with a wire hoping that might help so that I could mount it outside of the metal door (but still under the plastic, I don't want it showing) but it did not help much if at all.When it does operate either the voltage or current draw is lower than my door actuators expect and they begrudgingly lock/unlock. When I operate the power doors via the button in the car they are much more responsive.Also, it was rather difficult to understand which wiring diagram to use. Spent a whole afternoon to get it right and lucky I didn't blow any fuses honestly because at one point I wired something up and the wires started to get hot to the touch. You cannot install this product without a multimeter and some patience.For $17 I don't hate the product, but I would spend a little more for a better range and more "power." Again, I'm not sure if it's the voltage or the current which is low but either something isn't quite up to spec or I installed it not quite correctly.

Until I discovered that a lot of the Crown Victoria police interceptors have keyless entry hardware built in and just need a key FOB and a few minutes programming on Forscan to get it active, I was using these (after Bulldog stopped making their 1702). It works the same as any other keyless entry except for the major hassle of having to hold the trunk pop for 5 seconds, wait to see the lights flash, and then the trunk opens. I like the others that one quick press and trunk is open. But if you don't mind that the rest of the system works well with good range from the vehicle.

I like how it was only $15 bucks and easy to install. My lights blink and the car locks and unlocks just like a car alarm. Even comes with a blue LED blinking light for when the car is locked, to give a sense of a car alarm.I got the trunk open function wired up pretty easily but installing the actuator and getting it to work properly took a lot of troubleshooting.Just google your car’s wiring diagram and find the right colors under your dash.Connect the right color wires from your car to the Benvie’s wires, and in less than 30 mins I had a working system.You will need some extra wire of your own, the wires in this kit are way too short.My car is a 93 Del Sol and I hate using the key for the trunk and doors all the time. Now I have a button for my trunk and my driver side door. Eventually I’ll do the passenger side door too, but not a priority.The hard part is removing panels and tucking the wires.So in total, including the wiring, dash and side panel removal, troubleshooting, mounting lock/unlock actuators that cost like 5 bucks each, I probably spent like 4 hours. Lots of troubleshooting to get those actuators working properly every time you push the button, but the Benvie itself is easy to install and understand. Might be more difficult installing on a car that already comes with automatic door locks, but the actuators were easy to wire up following the wire diagram.I recommended it to a friend who also hates using the key to open the door, he couldn’t believe how much I paid!

I’ve been twisting wrenches for forty plus years and I am always looking for things that would make my life easier and and add value to vehicles I repair. I bought this not expecting very much but to me surprise it was a very nice buy. It was fairly easy to install ( just a little knowledge of how the door locks work). It was the right thickness to be able to easily place under the dash board. The wires were just the right length. The instructions that come with it seem to be vague at first but upon more inspection they are exactly spot-on. The instruction sheet specified the wiring for negative accurator , positive accurator or positive- negative accurators. Once you figure out what kind you have it’s very easy to wire.Simply put it is a very inexpensive way to add keyless entry to autos that have had them factory installed or adding keyless entry to a vehicle that has lost the key fob. It doesn’t have an alarm it just meant for automatic door locks.I was very pleasantly surprised with the quality of the device and the clicker is absolutely amazing looking and the quality of it is amazing as well.