RGBZONE 𝟰 𝗣𝗶𝗻 𝟭𝟬𝗺𝗺 𝗟𝗘𝗗 𝗦𝘁𝗿𝗶𝗽 𝗖𝗼𝗻𝗻𝗲𝗰𝘁𝗼𝗿 𝗞𝗶𝘁 32.8ft 4 Pin RGB Extension Wire and 5 Pcs 4 Pin LED Strip to Wire Connectors for 10mm IP20/IP65 5050 3528 SMD RGB LED Strip Light

This LED light strip extension/connector kit worked very well for my little project. I only needed to cut a light strip and reconnect the ends about 12 inches apart.I like that no wire strippers were required to use this. I do recommend sharp sheers for cutting the wires (and the light strip if it has a rubberized coating).The individual wires of the cable were easy to separate by hand as needed to insert them into the connector. The connector's prongs had no difficulty lining up with and cutting into the 4 wires to make a solid connection with the copper encased in each wire as I pushed the end of the connector closed.My LED light strip has a clear silicone coating. The connector had a little difficulty puncturing the silicone and making a connection with the LED strip. After turning it on, after installing the connection, I found that it did not work. I press more firmly on the connector and I could see the LED strip turn on, but when I release pressure it turned off again. I kept at this for a little bit and had to use a lot of force but eventually it locked into place and works perfectly fine. I think it just had to continue cutting into the silicone.When installing, be careful to keep the same alignment between the wires and both ends of the LED strip.The main disappointment with this kit is that it only includes five connectors. Why not six? There's plenty of wire, but if I plan to use it all I will need two separately buy a kit of connectors.

Good product. Just make sure when you look for a LED connector wire, you get the one that's compatible with your LED strip ( two, three, five pin, etc.)

I really liked how the wires did not need to be stripped. Make sure you puncture the LED strip from the top to ensure a good connection. If your connected LED strip doesn't turn on at first, make sure the wire is not just flipped backwards. The white wires were what I needed to look nice, but I wish there was no black writing on them. I wish the kit came with a way to stick the wire and the connectors to the wall. Overall good product and I couldn't find a better one on Amazon.

Like other reviews, given the length of wire provided, it would be nice to have at least 2 more connectors.I used this wire with 4-pin Govee strip lights. In order to ensure connection, I bent both ends of the connector pins slightly towards the inside of the connector. It did not look like the pins were perfectly aligned with the 2 outside strip light copper connections. After successful connection, I used a small set of needle nose pliers to close the connectors tightly to the wire and strip lights.

I purchased this one by mistake but I will say that it did work for the 8 mm size lights but I had to make a small adjustment to the pins in order for them to line up and make a good connection. They are easy to work with and will do the job for the correct width 10mm lights.

The media could not be loaded. I got this kit along with another kit to be able to locate strip lights in my karaoke cab minivan for new years eve.The first thing I had issues with was the no solder splicing connectors, some had already been mashed down so I had to pry them back open. The ones that were open closed fine. This is where things devolve. 2 out of the 4 connectors had shorts because the LED side couldn't make good contact.I used the 4 connectors, two on each of the controller pigtails and one side of the strip isn't matching the color of the other... Both sides are from the same spool of lights and I checked prior to cutting. As I didn't need both spools for my minivan's headliner. I'm leaving a similar review for the T / right angle connector kit I used.

Iffy on working some spots wants to work other spots don’t, first light strip i finally got it to work as i wrapped the strip around my kitchen cabinets, but when i almost finished the light , the last part wouldn’t connect (turn on) and the first part of the strip stayed red while first part of the strip changed colorsGot another strip but wouldn’t work at all, it’s this wire.. wish i went without a different one from the beginning

Extremely easy to use. Lined up perfect with the Wyze rgb led strips (non pro, not sure about pro). Connections work as expected. Note that the wires on the wire side need to be pulled apart in order to slide into holes. Highly recommend pulling them a little further than you need so you have some flexibility. If not, one wire will come out when you try to put in the next. I needed ONE more clip to finish my job but that was just bad planning on my part. You can order extra clips from the seller if you click on the seller link. Extremely happy to find this as their were no similar kits locally.